Stingray Emblem Installation
Jul 8, 2003 | 01:11 PM
Thread Starter
2nd Gear
Joined: Jun 2003
Posts: 2
Likes: 0
From: Oakville Ontario
Stingray Emblem Installation
I am replacing the stingray emblem which recently fell off on the highway. The replacement has 4 unthreaded pins and adhesive tape. Is this good enough or am I going to lose the new one eventually? Has anyone done anthing better? Please share with me what you did.
Jul 8, 2003 | 01:29 PM
Advanced
Joined: Sep 2002
Posts: 55
Likes: 0
Re: Stingray Emblem Installation (OakVette)
i have not had that problem. mine just popped in without adhesive tape. you may want to try some sheet metal nuts on the pins.
Jul 8, 2003 | 01:42 PM
Race Director
Joined: Apr 2003
Posts: 13,300
Likes: 16
From: TX
St. Jude Donor '12-'13
Re: Stingray Emblem Installation (coldwarrior2000)
I would just thread the pins (if they are long enough),
and put a nut behind the fender (if you can access the area.)
Jul 8, 2003 | 01:49 PM
Melting Slicks
Joined: Jun 2002
Posts: 2,609
Likes: 1
From: Behind the wheel of a large automobile
Re: Stingray Emblem Installation (bhblue80)
I think I'd be using some form of adhesive, just like the factory did.
Jul 8, 2003 | 02:18 PM
Melting Slicks
Joined: Oct 2002
Posts: 2,865
Likes: 1
From: I may be getting old but I refuse to grow up
Re: Stingray Emblem Installation (75Rag)
If everything is clean and free of wax, grease, or dirt when installed the tape should hold fine.
Steve :steering:
Jul 8, 2003 | 02:23 PM
Team Owner
Joined: Jun 2001
Posts: 23,367
Likes: 1,061
From: Virginia USA
Re: Stingray Emblem Installation (OakVette)
What year is your car. On my 71 the pins stick through the quarter panel and then have what is called pal nuts on the pins. The pal nuts are self threading and actually cut the threads on the pins as you screw them on. I could access all the pins by removing my gills. My emblems did not have any tape on them at all.
Jul 8, 2003 | 02:58 PM
Safety Car
Joined: Aug 2000
Posts: 3,943
Likes: 44
From: Florham Park NJ Port Credit Ontario
Re: Stingray Emblem Installation (theandies)
My 74 had no "Acorn nuts" just adhesive.
Jul 8, 2003 | 03:06 PM
Melting Slicks
Joined: Nov 1999
Posts: 2,372
Likes: 227
From: N Cal
Re: Stingray Emblem Installation (OakVette)
The factory emblem only had adhesive, the pins are for alignment only no speed nuts!
Top 10 DOs and DON'Ts for Protecting Your Convertible Top!
Michael S. Palmer
Top 10 Most Explosive Corvettes Ever Made: Power-to-Weight Ratio Ranked!
Joe Kucinski
150 hp to 1,250 hp: Every Corvette Generation Compared by the Specs That Matter
Joe Kucinski
8 Coolest Corvette Pace Cars (and Replicas) of All Time
Verdad Gallardo
Top 10 Corvette Engines RANKED by Peak Torque (70+ Years of Muscle!)
Joe Kucinski
Corvette ZR1X Will Be Pacing the Indy 500, And Could Probably Race, Too!
Verdad Gallardo
Top 10 Corvettes Coming to Mecum Indy 2026!
Brett Foote
Top 10 C9 Corvette MUST-HAVES to Fix These C8 Generation Flaws!
Michael S. Palmer
10 Revolutionary 'Corvette Firsts' Most People Don't Know
Joe Kucinski
5 Reasons to Upgrade to an LS6-Powered Corvette; 5 Reasons to Stay LT2
Michael S. Palmer
Jul 8, 2003 | 03:44 PM
Drifting
Joined: Dec 2002
Posts: 1,426
Likes: 1
From: San Diego, CA Website: ChrisMitchell.us
Re: Stingray Emblem Installation (OakVette)
My original emblems (cross flags) had both nuts and a tape backing. The GM NOS replacements I bought also had both the nuts and tape.
If at all possible you should use both, just to be sure.
:cheers:
Jul 8, 2003 | 06:01 PM
Instructor
Joined: Jun 2003
Posts: 156
Likes: 12
From: Arkansas
Re: Stingray Emblem Installation (theandies)
how do you remove the eggcrates?
:confused:
Jul 8, 2003 | 08:38 PM
Team Owner
Joined: Jun 2001
Posts: 23,367
Likes: 1,061
From: Virginia USA
Re: Stingray Emblem Installation (olelucky)
Quote:
how do you remove the eggcrates?
:confused:
Two screws at the top and a stud with a nut at the bottom. Look under the car towards the rocker panel and you'll see what I'm talking about.
Jul 8, 2003 | 10:36 PM
Pro
Joined: Jan 2000
Posts: 672
Likes: 0
From: Flanders N.J.
Re: Stingray Emblem Installation (OakVette)
Duct tape...
Only kidding.
apply ,
c3 ,
cheap ,
corvette ,
emblem ,
emblems ,
embles ,
fell ,
install ,
installation ,
metal ,
nuts ,
placement ,
rear ,
stingray