Check em out!
Thread Starter
Pro
Joined: Mar 2000
Posts: 669
Likes: 80
From: NE USA
Check em out!
Still have to figure out rerouting the spark plug wires and looms. Then I have to come up with something for the dipstick. I just hope the headers are the right ones as it might be a while before I actually get them installed.
Team Owner
Joined: Dec 1999
Posts: 26,555
Likes: 257
From: Florida
2021 C2 of the Year Finalist - Modified
C2 of the Year Finalist - Modified 2020
C2 of Year Finalist (performance mods) 2019
St. Jude Donor '03 thru '26
Re: Check em out! (verskel)
They look a lot like DynoMax! :)
Race Director
Joined: Mar 2001
Posts: 11,322
Likes: 1
From: Living in the Hartland
Re: Check em out! (C3w4sp)
I am using these:
http://store.summitracing.com/partde...57#largerimage
and this:
http://store.summitracing.com/partde...57#largerimage
Just make sure you check it when the eng is cold. :)
http://store.summitracing.com/partde...57#largerimage
and this:
http://store.summitracing.com/partde...57#largerimage
Just make sure you check it when the eng is cold. :)
Thread Starter
Pro
Joined: Mar 2000
Posts: 669
Likes: 80
From: NE USA
Re: Check em out! (Fevre)
Fevre
The R & M's are my first choice. I have centerbolt valve covers and they make some looms just for them. I 'm using 8.5mm MSD superconductors and I don't know if the holes in the R & M's are big enough, what do you think?
The R & M's are my first choice. I have centerbolt valve covers and they make some looms just for them. I 'm using 8.5mm MSD superconductors and I don't know if the holes in the R & M's are big enough, what do you think?
Race Director
Joined: Mar 2001
Posts: 11,322
Likes: 1
From: Living in the Hartland
Re: Check em out! (C3w4sp)
I went with these on my Formula with center bolt covers:
http://store.summitracing.com/partde...5035611&view=1
It says for 7-8 mm wires but I have 8mm Accel wires and they will slide in the looms if you pull on them so I bet you could squeeze 8.8mm in em. I was going to go with the R&Ms but wanted something a little diff than my vette.
http://store.summitracing.com/partde...5035611&view=1
It says for 7-8 mm wires but I have 8mm Accel wires and they will slide in the looms if you pull on them so I bet you could squeeze 8.8mm in em. I was going to go with the R&Ms but wanted something a little diff than my vette.
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
Top 10 Most Expensive Corvettes Ever Sold on Bring A Trailer
Brett Foote
10 Things Every Corvette Owner Needs (2026 Edition)
Michael S. Palmer
8 Most "Only Corvette Owners Understand" Quirks and Problems
Pouria Savadkouei
10 Reasons the C6 Z06 is Still A Performance Benchmark After 20 Years
Joe Kucinski
How Much Horsepower Every Corvette Engine "LOST" in 1972
Joe Kucinski
Top 10 DOs and DON'Ts for Protecting Your Convertible Top!
Michael S. Palmer
Top 10 Most Explosive Corvettes Ever Made: Power-to-Weight Ratio Ranked!
Joe Kucinski
150 hp to 1,250 hp: Every Corvette Generation Compared by the Specs That Matter
Joe Kucinski
8 Coolest Corvette Pace Cars (and Replicas) of All Time
Verdad Gallardo
Le Mans Master
Joined: Jan 2001
Posts: 6,938
Likes: 1
From: San Diego CA
Re: Check em out! (Fevre)
Race Director
Joined: Mar 2001
Posts: 11,322
Likes: 1
From: Living in the Hartland
Re: Check em out! (C3w4sp)
Fevre, how tight are the R & M's on your wires?
