F/S Built LS1 Engine from my swap
#1
F/S Built LS1 Engine from my swap
I am considering selling my Built LS1 engine from my 93 Vette. I have had fun with the car and during the build but my wife and I are going to try to have kids soon and I better get ahead of the game. I finished the motor and installed it about 6000 miles ago and have no problems with it.
Engine Specs
LS1 aluminum block
241 center bolt heads
.005 overbore
Mahle Pistons and low friction rings
Eagle Rods
Stock Crank
FMS Custom Grind Camshaft - 232"/236" .585"/.600" 114LSA - aggressive profile with a 2800-7000 RPM range, rough idle, recommended for blower/nitrous applications
Valve springs installed that match the recommendations for the cam lift
LS2 intake and crossover tubes
102mm TB.
01 C5 Batwing oil pan with split bottom design
The block is painted corvette red
All acc. with the engine to include kwik performance high mount alt bracket and ps braket
new alternator
new starter
new c6 waterpump
maf sensor and the map sensor come with the motor
01 c5 manifolds that clear the frame of the c4 vette
I will also include the engine mounts to attach it to a stock c4 corvette engine mount and still leave room to retain your factory windshield wiper motor.
I currently have a 4l60e trans attached to it which was fully built around 30k miles ago that I purchased used out of a 06 GTO and I put about 5000 on it since then. The trans shifts hard,fast, and strong no slipping and it has a 2800 rpm tq convertor which matches the start of the power curve of the futral f9 cam. The trans does need new main and tail shaft seals and a new pan gasket due to some small leaks but nothing that is to terrible.
I will sell then engine alone for 5000 or both engine and trans for 5500. I am in no rush as of now to sell it so please do not low ball I have much more than this invested in the setup. The engine and trans are still currently in the car and can be heard running. I will post pictures below. You can either PM myself or send me a text at 330 936 1317.
I will not ship any of the items listed you must pick them up, I am located in Richlands, NC. Thank you for reading and have a Merry Christmas and Happy New Year
Engine installed in car
Engine on stand after painting
Side view of engine mount plate with lt1 mount attached
Engine Specs
LS1 aluminum block
241 center bolt heads
.005 overbore
Mahle Pistons and low friction rings
Eagle Rods
Stock Crank
FMS Custom Grind Camshaft - 232"/236" .585"/.600" 114LSA - aggressive profile with a 2800-7000 RPM range, rough idle, recommended for blower/nitrous applications
Valve springs installed that match the recommendations for the cam lift
LS2 intake and crossover tubes
102mm TB.
01 C5 Batwing oil pan with split bottom design
The block is painted corvette red
All acc. with the engine to include kwik performance high mount alt bracket and ps braket
new alternator
new starter
new c6 waterpump
maf sensor and the map sensor come with the motor
01 c5 manifolds that clear the frame of the c4 vette
I will also include the engine mounts to attach it to a stock c4 corvette engine mount and still leave room to retain your factory windshield wiper motor.
I currently have a 4l60e trans attached to it which was fully built around 30k miles ago that I purchased used out of a 06 GTO and I put about 5000 on it since then. The trans shifts hard,fast, and strong no slipping and it has a 2800 rpm tq convertor which matches the start of the power curve of the futral f9 cam. The trans does need new main and tail shaft seals and a new pan gasket due to some small leaks but nothing that is to terrible.
I will sell then engine alone for 5000 or both engine and trans for 5500. I am in no rush as of now to sell it so please do not low ball I have much more than this invested in the setup. The engine and trans are still currently in the car and can be heard running. I will post pictures below. You can either PM myself or send me a text at 330 936 1317.
I will not ship any of the items listed you must pick them up, I am located in Richlands, NC. Thank you for reading and have a Merry Christmas and Happy New Year
Engine installed in car
Engine on stand after painting
Side view of engine mount plate with lt1 mount attached
Last edited by Chad30021; 12-24-2013 at 04:28 PM.
#2
Burning Brakes
That would be cool, but I wouldn't know where to start with the wiring and fuel..
#5
Cruising
Member Since: Jun 2013
Location: Guyton Georgia
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
If you still have it, the second week of January, I will come take off your hands
I'm waiting on a check to come in.
They keep telling "the check is in the mail"
Mike
I'm waiting on a check to come in.
They keep telling "the check is in the mail"
Mike
Last edited by MCAF1; 12-25-2013 at 05:53 PM. Reason: add to the message
#11
Burning Brakes