1QWKZ28

For Sale:

396 Assembled Long Block
Bore .30 Stroke 3.875
Lunati 4340 Forged Steel Crankshafts
Oliver Splayed 4 bolt mains
ARP Fasteners
Lunati Forged Steel Pro Rods
SRP Flat Top Pistons (12.5:1)
Rotating Assembly Balanced
Sealed Power Plasma Moly Rings
Clevite 77 H-Series Race Bearings
Melling High Pressure Oil Pump
Canton Oil Pan
Electric Water Pump
42# Fuel Injectors
Comp double roller timing chain
95+ vented optispark (NEW)
58mm TB

GTP STAGE III LT4 Heads/Intake (gasket matched)
(2.02/1.57 Farea valves)

Flow numbers:
Lift Intake Exhaust
-------------------------------------
.200 152 108
.300 204 172
.400 246 199
.500 275 210
.550 283 213
.600 292 216

Solid Roller Valve Train
Cam Motions Cam
(.50 258/268 .683/.672 114LS) Comp Solid Lifters Double Springs (from GTP)
Titanium Retainers (from GTP) Comp Cams Moly Push rods

This engine package is fully assembled and ready to go. Intake and little things like the water pump and opti will be packaged separately, so that you dont have to disassemble it for installation.

Price is $8,000 OBO to the first person with the money.
(Buyer must pick up or arrange and pay for shipping, located in Tampa, FL)

The pictures below are of the engine fully dressed with a Z28 accessory bracket. It was going into a Z, but not anymore. http://www.hipaa4u.com/images/auctions/Engine1.jpg http://www.hipaa4u.com/images/auctions/Engine2.jpg http://www.hipaa4u.com/images/auctions/Engine3.jpg http://www.hipaa4u.com/images/auctions/Engine4.jpg http://www.hipaa4u.com/images/auctions/Engine5.jpg

Email me: kienastc@hotmail.com

1QWKZ28

Up Up Up

MrNuke

Is there a dyno sheet available?
Was this professionally built with warranty?

1QWKZ28

No dynosheet.
The bottom end was built by RaceNet, but we took it all apart to verify everything and put it back together. Heard too many stories of other shops not putting in what you paid for.
Nobody offers a warranty on a race engine.

Curt

luvmy92

Just out of curiousity... why are you selling?

Mike

1QWKZ28

I dont have the time anymore for racing due to a new business venture. I have sold both my race cars, truck, trailer. This is the last engine I have left.

Curt

luvmy92

Thanks for the response. Did RaceNet do all the machine work as well? I would feel a lot better if you dyno'd it prior to laying out that kind of scratch. Just so you know, I'm in the Orlando area and am interested.

Mike

1QWKZ28

RaceNet did all the machine work on the bottom end. GTP did all the head and intake work.

I am not interested in dynoing the motor. I put over 14k into this setup, if someone doesnt think it is worth 8k, then its not a real big deal to me. Im taking a loss as it is.

I have let people come look at it and see the parts and even tore it down for a potential person, but Im not going to go through the time of dynoing it.
You cant call up any engine builder and expect them to dyno an engine unless you pay for it.

Curt

luvmy92

I'm fully aware of what you have in your motor, as I have the same amount tied up in mine (including labor) but still have the stock bottom end.

While the price is outstanding, I'm the type of buyer that likes to know what they are getting for their money. I'm sure you'll have no problem selling it however. It sure is beautiful...

Mike

1QWKZ28

Mike,

I appreciate the feedback. I wish I had the time to dyno the motor and post some real numbers, but if I had time for that I probably would not need to sell it as well. Thanks again.

Curt

wheeljo2

How much HP was it projected to make and what was the estimated MPH in the 1/4 mile. Will it hold up to nitrous ??

Thanks.

1QWKZ28

I was shooting for 500 RWHP.
Too many factors for 1/4 mph.

It will easily hold up to a 500HP shot of nitrous.

1QWKZ28

^^^UP

SonnyinVA

did you have racenet add the lunati crank as extra or especially for you? their strokers don't usually come with lunati cranks...

1QWKZ28

Cola cranks were on backorder at the time.

larryfs

so what kind of PCM tuning would you need with that??

1QWKZ28

Definitely need someone who knows how to program a stock PCM. Otherwise you better run a FAST or DFI. Either will work, but a stock PCM will never be able to produce as much as a DFI.

1QWKZ28

to the top;

1QWKZ28

UP UP UP

1QWKZ28

UP UP UP to the TOP