Heads combo
Thread Starter
Melting Slicks
Joined: Oct 2000
Posts: 3,010
Likes: 1
From: Sweden/Stockholm
Heads combo
Hello m8s.
What heads would you recomend with this combo.
355
CC503 cam
LT1 intake.
Heders
3" exhaust
Car is a -90 six speed.
(car will not need to pass emission)
I looked at the following heads.
Edelbrock Performer RPM
Canfield ( JEGS ) alu heads
And Trickflow 23 heads.
What I like with the Edelbrock Performer RPM is that its a 170 intake port. What I been told is that 170cc intake port volume providing greater torque down low especially with a non-stroker engine.
Please let me know what you think.
Regards
What heads would you recomend with this combo.
355
CC503 cam
LT1 intake.
Heders
3" exhaust
Car is a -90 six speed.
(car will not need to pass emission)
I looked at the following heads.
Edelbrock Performer RPM
Canfield ( JEGS ) alu heads
And Trickflow 23 heads.
What I like with the Edelbrock Performer RPM is that its a 170 intake port. What I been told is that 170cc intake port volume providing greater torque down low especially with a non-stroker engine.
Please let me know what you think.
Regards
Race Director
Joined: May 2003
Posts: 10,749
Likes: 41
Originally Posted by devilfish
Hello m8s.
What heads would you recomend with this combo.
355
CC503 cam
LT1 intake.
Heders
3" exhaust
Car is a -90 six speed.
(car will not need to pass emission)
I looked at the following heads.
Edelbrock Performer RPM
Canfield ( JEGS ) alu heads
And Trickflow 23 heads.
What I like with the Edelbrock Performer RPM is that its a 170 intake port. What I been told is that 170cc intake port volume providing greater torque down low especially with a non-stroker engine.
Please let me know what you think.
Regards
What heads would you recomend with this combo.
355
CC503 cam
LT1 intake.
Heders
3" exhaust
Car is a -90 six speed.
(car will not need to pass emission)
I looked at the following heads.
Edelbrock Performer RPM
Canfield ( JEGS ) alu heads
And Trickflow 23 heads.
What I like with the Edelbrock Performer RPM is that its a 170 intake port. What I been told is that 170cc intake port volume providing greater torque down low especially with a non-stroker engine.
Please let me know what you think.
Regards
If your thinking about Trickflow heads. I have a BRAND NEW set that are for sale. I have even had them flow benched. I have seen the Edelbrocks on the bench, They are horrible. To each is own, but if I was going with a setup like yours, I would want a set of heads that flowed well. My heads were $1235 US New. You can make me an offer.
Le Mans Master
Joined: Sep 2000
Posts: 6,303
Likes: 714
From: Bartlett IL
I can vouch for the TFS 23 heads. Mine is a 350 Xfire with a retro-fit roller cam and there is absolutely no loss of low end torque. Last dyno run had it at 347rwtq @ 3800rpm. I'm using 11" ZR-1 wheels and breaks tires loose in second.
Thread Starter
Melting Slicks
Joined: Oct 2000
Posts: 3,010
Likes: 1
From: Sweden/Stockholm
ok I see..
What about the JEGS heads, the price is almost the same.
Ayone got some experince with those?
http://www.jegs.com/webapp/wcs/store...0187&langId=-1
Regards
Devil
What about the JEGS heads, the price is almost the same.
Ayone got some experince with those?
http://www.jegs.com/webapp/wcs/store...0187&langId=-1
Regards
Devil
