Cam install?
Thread Starter
Melting Slicks
Joined: May 2006
Posts: 3,385
Likes: 4
From: King George VA
Cam install?
Anyone do a cam install with the engine still in the car? Was it to difficult? What kinda cam can I use with the stocks heads that will give me good power? Ill upgrade the heads alittle later.
Race Director
Joined: Jan 2002
Posts: 12,263
Likes: 86
From: O'Fallon Missouri
I've done two cam swaps with the engine in the car. First one took around 20 hours, second about 10.
Before you pick a camshaft you need to decide what you want out of the car performance wise. High revs, low end torque, emissions compliant, and future upgrades?
If you are going to be doing the heads anytime soon. I would just wait to get a heads/cam package from one of the big tuners.
Before you pick a camshaft you need to decide what you want out of the car performance wise. High revs, low end torque, emissions compliant, and future upgrades?
If you are going to be doing the heads anytime soon. I would just wait to get a heads/cam package from one of the big tuners.
Race Director
Joined: Jan 2002
Posts: 12,263
Likes: 86
From: O'Fallon Missouri
Originally Posted by 93-383
installation of a cam with engine inthe car is possible but a pain. most years of c4 have a frame crossmember infront of the engine. This either completely or partialy obstructs the cam shaft from removal
Le Mans Master
Joined: Oct 2004
Posts: 7,706
Likes: 485
From: Everett WA
C4 of Year Finalist (appearance mods) 2019
The LT4 hot cam kit is supposed to be quite good and still maintains complete streetability. Comes with a set of roller rockers in the kit.
Check this out. www.geocities.com/MotorCity/Downs/4013/lt4.html
How did your day at TJ Wong's go?
Check this out. www.geocities.com/MotorCity/Downs/4013/lt4.html
How did your day at TJ Wong's go?
Burning Brakes
Joined: Nov 2005
Posts: 908
Likes: 1
From: Colorado Springs Colorado
I almost did. Once I felt the condition of the cam bearings, I pulled it out for a rebuild. Ya just never know what you're gonna find till you look.
BTW, IIRC you do have to pull the radiator to get the cam in and out. That's a PITA too. Good luck with the oil pan, that's another one that is tough to get sealed properly with the engine in place, but I'm sure it can be done with care and patience.
BTW, IIRC you do have to pull the radiator to get the cam in and out. That's a PITA too. Good luck with the oil pan, that's another one that is tough to get sealed properly with the engine in place, but I'm sure it can be done with care and patience.
Burning Brakes
Joined: Oct 2006
Posts: 834
Likes: 0
Originally Posted by scranage
I almost did. Once I felt the condition of the cam bearings, I pulled it out for a rebuild. Ya just never know what you're gonna find till you look.
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
Top 10 Most Expensive Corvettes Ever Sold on Bring A Trailer
Brett Foote
10 Things Every Corvette Owner Needs (2026 Edition)
Michael S. Palmer
8 Most "Only Corvette Owners Understand" Quirks and Problems
Pouria Savadkouei
10 Reasons the C6 Z06 is Still A Performance Benchmark After 20 Years
Joe Kucinski
How Much Horsepower Every Corvette Engine "LOST" in 1972
Joe Kucinski
Top 10 DOs and DON'Ts for Protecting Your Convertible Top!
Michael S. Palmer
Top 10 Most Explosive Corvettes Ever Made: Power-to-Weight Ratio Ranked!
Joe Kucinski
150 hp to 1,250 hp: Every Corvette Generation Compared by the Specs That Matter
Joe Kucinski
