Attempting to use winaldl on my '90 with the 1227727 ECM and all I get is 255 in the MW2 on the raw data page. Even that quits when I turn the key on or start the car. Is it possible to use this software for my car or what other one should I use???

Thanks,
Roger

 

Try Datamaster or TunerPro RT.

WinALDL Info below:

Supported ECM types
===================
WinALDL Selection
Supported Vehicles
Comment
------------------------------------------------------
1227747, 1228062
1986-88 4.3 TBI 'Z' LB4
1987-88 5.0 TBI 'H' L03 TRUCKS
1987-88 5.7 TBI 'K' L05 TRUCKS
MW2 uses "Idle Flag" and "High Bat Voltage"
MWAF1 uses "Clear Flood Flag"

1986-91 2.8 TBI 'R' LL2 TRUCKS
1989 3.1 TBI 'D' LG6 TRUCKS
1992-93 2.8 TBI 'R' LL2 S TRUCK
1988 4.3 TBI 'Z' LB4 CARS
MW2 uses "Cool Flag" and "High Bat Voltage"
MWAF1 uses "Not Closed Loop"

1989 4.3 TBI 'Z' LB4 TRUCKS
1990-01 4.3 TBI 'Z' LB4 S/T TRUCKS w/auto TRANS
1990 4.3 TBI 'Z' LB4 C/K/G/M/L/R/V TRUCKS
1990 4.3 TBI 'B' LU2 TRUCKS
1989-90 5.0 TBI 'H' L03 TRUCKS
1989 5.7 TBI 'K' L05 TRUCKS
1990 5.7 TBI 'K' L05 TRUCKS LIGHT DUTY EMISSIONS
1989 6.0 TBI 'P' LS0 TRUCKS
1989 7.4 TBI 'N' L19 TRUCKS
1990-91 7.4 TBI 'N' L19 TRUCKS LIGHT DUTY EMISSIONS
MW2 uses "Idle Flag" and "1st Time Idle Flag"
MWAF1 uses "Clear Flood Flag"

1989-90 4.3 TBI 'Z' LB4 CARS
MW2 uses "Idle Flag" and "High Bat Voltage"
MWAF1 uses "Not Closed Loop"

1227170
1986-88 2.8 V6 MPFI '9' L44

1228746
1988 5.0 V8 TBI LO3
1989-92 5.0 V8 TBI 'E' L03 ('F' body)
1989-90 5.0 V8 TBI 'E' L03 ('B' body)
1989-90 5.7 V8 TBI '7' L05 ('B' body)

1225550, 1225570, 1225610
1982 5.0 V8 CFI '7' LU5
1982 5.7 V8 CFI '8' L83
1982-86 1.8 L4 TBI 'O' LH8
1982-86 2.5 L4 TBI 'R' LR8
1982-86 2.5 L4 TBI 'U' L68
1982-86 2.5 L4 TBI '2' LQ9
1985-86 2.5 L4 TBI 'E' LN8
1983 5.0 V8 CFI 'S' LU5

1227808
VN & VP Holden Commodore

CLCC 1984 truck
CLCC 1984 Truck

CLCC 1984 car, 1985, 1986
CLCC 1984 Car, 1985, 1986

1985 2.8 litre MPI
1985 2.8 litre MPI

1986 2.8 litre MPI
1986 2.8 litre MPI

1226870
1985 5.0 V8 PFI 'F' LB9
1985 5.7 V8 PFI '8' L98

1227165
1986-89 5.0 V8 PFI 'F' LB9
1986-89 5.7 V8 PFI '8' L98

1227148
1986-88 3.8 SFI '3' LG3
1986-91 3.8 SFI '7' LC2
1986-87 3.8 SFI 'B' LG2

1226026
1985 4.3 V6 TBI 'Z' LB4
1985 5.0 V8 CFI '5' LB9
1983-85 5.7 V8 CFI '8' L83

16144288
4.3L TBI (LB4) (VIN=Z) 90 C/K TRUCK
4.3L TBI (LB4) (VIN=Z) 91 S/T TRUCK W/MANUAL TRANSMISSION
4.3L TBI (LB4) (VIN=Z) 91 C,K,G,M,L TRUCK W/MANUAL TRANSMIS
4.3L TBI (LB4) (VIN=Z) 90 M/L/G
4.3L TBI (LB4) (VIN=Z) 90 S/T TRUCK W/MANUAL TRANSMISSION
4.3L TBI (LB4) (VIN=Z) 92 C,K,S,T,M,L,G TRUCK
4.3L TBI (LB4) (VIN=Z) 93 C,K TRUCK
MW2 uses "1st time Idle Flag" and "ESC 43B Ready for PE"
MWAF1 uses "Old High Gear Flag" and "4-3 Downshift for TCC unlock"
MCU2IO uses "AIR Divert" and "AIR Switch"
Sensor uses "FP Switch Voltage" (Fuel Pump)

3.1L TBI (LG6) (VIN=D) 91 U VAN
3.1L TBI (LG6) (VIN=D) 92 U VAN
3.1L TBI (LG6) (VIN=D) 93 U VAN
3.1L TBI (LG6) (VIN=D) 94 1,2,3U VAN
3.1L TBI (LG6) (VIN=D) 95 1,2,3U VAN
MW2 uses "High Bat Voltage" and "ESC 43B Ready for PE"
MWAF1 uses "Old High Gear Flag" and "4-3 Downshift for TCC unlock"
MCU2IO uses "Fan #1", "Fan #2" and "Heated Windshield"
Sensor uses "FP Switch Voltage" (Fuel Pump)

6.0L TBI (LS0) (VIN=P) 91
7.0L TBI (LR0) (VIN=M) 91
6.0L TBI (LS0) (VIN=P) 92 GMT530 TRUCK
7.0L TBI (LR0) (VIN=M) 92 GMT530 TRUCK
6.0L TBI (LS0) (VIN=P) 93 GMT530 TRUCK
7.0L TBI (LR0) (VIN=M) 93 GMT530 TRUCK
6.0L TBI (LS0) (VIN=P) 94 GMT530 TRUCK
7.0L TBI (LR0) (VIN=M) 94 GMT530 TRUCK
6.0L TBI (LS0) (VIN=P) 95 GMT530 TRUCK
7.0L TBI (LR0) (VIN=M) 95 GMT530 TRUCK
MW2 uses "1st time Idle Flag" and "OL Idle Flag"
MWAF1 uses "CL Idle" and "AF Cold Park"
MCU2IO uses "Idle Kicker Switch" and "Idle Kicker Light"
Sensor uses "PS Switch Voltage" (Power Steering)

5.0L TBI L03 VIN=H 92 C,K,G
5.7L TBI L05 VIN=K 92 C,K,G,R,V
5.0L TBI L03 VIN=H 93 C,K
5.7L TBI L05 VIN=K 93 C,K,P
5.0L TBI L03 VIN=H 94 C,K
5.7L TBI L05 VIN=K 94 C,K,P
5.0L TBI L03 VIN=H 95 C,K
5.7L TBI L05 VIN=K 95 C,K,P
5.7L TBI L05 VIN=K 92 CNG COMPRESSED NATURAL GAS G VAN & C/K TRUCK
MW2 uses "1st time Idle Flag" and "OL Idle Flag"
MWAF1 uses "CL Idle" and "AF Cold Park"
MCU2IO uses "AIR Divert" and "AIR Switch"
Sensor uses "FP Switch Voltage" (Fuel Pump)

 

Thanks !

I download Datamaster and it connects up and reads just fine...Now I have another problem....I went out to start the car and it just cranks over but will not fire. The Datamaster shows 0.0 on the inj volts and it is highlighted in yellow. tried the VATS but dosen't look like it is active so I am at a loss....any ideas??