need comfirmation on half shaft
Thread Starter
Melting Slicks
Joined: Feb 2005
Posts: 2,135
Likes: 0
From: Sebastian Florida
St. Jude Donor '06
need comfirmation on half shaft
Been fighting a bad clunk when shifting from 1-2 and 2-3, well went to replace the ujoints(again) and one cap slid right on with almost no effort.
Is this a sign of a bad half shaft?
Is this a sign of a bad half shaft?
Drifting
Joined: Jan 2006
Posts: 1,740
Likes: 2
From: Winchester Virginia
WOW, That's bad!.............
Couple of questions that may or may not be relevant in the long run, but first things first!
1. Was this on just one side of the 1/2 shaft or both ends? (same U-joint, different results=bad hole)
2. What U-Joints did you use? (just a sanity check to make sure they are the right replacement U-joints)
3. Do you have any way to check the ID of the 1/2 shaft compared to that of the other side? (see if anything is out of spec, or wrong size hole to cap ratio)
4. Does a visual show any elongation of the 1/2 shaft end? (should be somewhat visible if the hole is bad)
With 1/2 shafts being relatively cheap, and members here having some laying around, I'd just replace it.
I hope this helps!
R/Noland
Couple of questions that may or may not be relevant in the long run, but first things first!
1. Was this on just one side of the 1/2 shaft or both ends? (same U-joint, different results=bad hole)
2. What U-Joints did you use? (just a sanity check to make sure they are the right replacement U-joints)
3. Do you have any way to check the ID of the 1/2 shaft compared to that of the other side? (see if anything is out of spec, or wrong size hole to cap ratio)
4. Does a visual show any elongation of the 1/2 shaft end? (should be somewhat visible if the hole is bad)
With 1/2 shafts being relatively cheap, and members here having some laying around, I'd just replace it.
I hope this helps!
R/Noland
Last edited by BlackHarleyMan; Mar 26, 2009 at 09:13 PM.
Thread Starter
Melting Slicks
Joined: Feb 2005
Posts: 2,135
Likes: 0
From: Sebastian Florida
St. Jude Donor '06
This was a brand new Brute Force ujoint, havent tried to put another ujoint in there yet.
Wish I did have something to measure the ID, old ujoints were only 3 mths old.
Tried the light trick and could not see any light w/cap on.
Wish I did have something to measure the ID, old ujoints were only 3 mths old.
Tried the light trick and could not see any light w/cap on.
Drifting
Joined: Jan 2006
Posts: 1,740
Likes: 2
From: Winchester Virginia
R/Noland
Drifting
Joined: Jan 2006
Posts: 1,740
Likes: 2
From: Winchester Virginia
Well, Unless Brute Force just all of a sudden starting having major quality control issues, or someone was high at work when YOUR J-joint was packed up, then I'm voting for a bad U-Joint Hole!
Just go to the For Sale section and ask to see if anyone has one. I have one but I'm going to need it for my 55 Chevy PU.
Check with Y-ME and see if Dan has any laying around, he should be able to help!
R/Noland
Just go to the For Sale section and ask to see if anyone has one. I have one but I'm going to need it for my 55 Chevy PU.
Check with Y-ME and see if Dan has any laying around, he should be able to help!
R/Noland
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
5 Best & 5 Worst Corvette Daily Drivers
Joe Kucinski
The Headlights of Every Corvette Generation Explained
Joe Kucinski
5 Best & 5 Most Overrated Corvette Track Packages of All Time!
Joe Kucinski
Every 2027 Corvette Engine Explained
Joe Kucinski
Designer Imagines A Corvette That Looks More Like a Corvette Than the Corvette
Verdad Gallardo
10 Ugly Corvettes That We Still Kinda Love
Joe Kucinski
Top 10 Most Expensive Corvettes Ever Sold on Bring A Trailer
Brett Foote
10 Things Every Corvette Owner Needs (2026 Edition)
Michael S. Palmer
8 Most "Only Corvette Owners Understand" Quirks and Problems
Pouria Savadkouei
Team Owner
Joined: Sep 2003
Posts: 25,412
Likes: 2,745
Nothing you've mentioned confirms that possibly a cap on the joint was swapped in the package! It happens frequently in the parts stores! If you've got your old joints still hanging around, take a couple of those caps and try them in the end yoke! Take your half shaft to a parts store and have them try an "off the shelf" new joint "first"!
An inexpensive vernier caliper is a wise buy! You'll use it often!!!!
I would doubt that you've "demolished" just one eye on the end yoke!
An inexpensive vernier caliper is a wise buy! You'll use it often!!!!
I would doubt that you've "demolished" just one eye on the end yoke!
Last edited by WVZR-1; Mar 26, 2009 at 08:43 PM.
Drifting
Joined: Jan 2006
Posts: 1,740
Likes: 2
From: Winchester Virginia
Dave good advice but check what I asked in Post #2
3. Do you have any way to check the ID of the 1/2 shaft compared to that of the other side? (see if anything is out of spec, or wrong size hole to cap ratio)
R/Noland
3. Do you have any way to check the ID of the 1/2 shaft compared to that of the other side? (see if anything is out of spec, or wrong size hole to cap ratio)
R/Noland
Last edited by BlackHarleyMan; Mar 26, 2009 at 09:13 PM.
