Magnetos ?
#21
Drifting
Member Since: Aug 2006
Location: Canandaigua New York
Posts: 1,624
Likes: 0
Received 1 Like
on
1 Post
Oh.. and make sure you don't take your iron pills before going in to visit with him or you could be in a world of hurt...
#24
I dare any of you guys that are Super He Men to grab onto one of my Blueprinted and Very Hot OAC internal coil Vertex Magnetos while I spin the bronze drive gear by hand.
Spin it maybe 50 RPM's only.
You will likely pee your pants.
Your arm and neck will start convulsing without any self control.
The filthiest words and phrases imaginable will come from your mouth for the next half hour.
When I put that same Vertex magneto into my modified SUN Distributor Machine and spin it up to 9,000RPM's + with the spark gap rack set to 2" inches air gap.........
I will pay you $500.00 cash to stick your hand in there.
LOL
A really hot modified OAX external coil Vertex Mag will fire cleanly with a 4 inch air gap across all 8 spark plugs while spinning at 9K+.
Right around 80K - 100K thousand volts @ 200MA current.
Hot Brilliant Blue Sparks.
Any takers or dare devils?
Magneto Man......... I like that.
I have been hit- secondary High KV shocked with MSD6 & MSD7 ignitions while spin testing them at high RPMs.
MSD's feel like a Bee Sting to me compared to any HOT Firing Vertex Magneto.
BR
Last edited by 87 vette 81 big girl; 03-25-2011 at 10:58 PM.
#25
I was taught by late friend also to repair magnetos.
He showed me all of his own tricks and 50 + years of experience repairing them.
He was one of 2 AFA Licensed Aviation Magneto Repair Service people in the USA.
Right in my home area.
He only taught me, no one else.
Come on GUYS, You all want to take me down and Humiliate me..........
Tell you what I am going to do for You............
I will shock myself 1st with my hottest running Vertex Magneto....
I will grab the Vertex magneto cap with my left hand and spin the bronze gear as fast as I can.
Show You I can take the extreme electrical High KV shock Pain.
Then I will hand the magneto to you and let you shock me..........
With my left hand I will grab the magneto cap.
Spin as fast as you can.
I can take it.
Then I will pull a $100 bill out of my pocket and set it on the table.
To earn it 1st, You have to grab the magneto cap with your left of right hand and let me spin it.
I will turn it maybe 1/2 RPM's what You did to me.
I will give you the $100 Bill then to keep.
You earned my respect.
You will earn mine too.
My late buddie and me would take turns shocking each other with those Hot Vertex mags spinning by hand to see he could take it longer.
About a Tie.
About 30 seconds each.
Neither of us Peed our pants.
Sure was fun though seeing who was tougher and crazier.
LOL
Brian
He showed me all of his own tricks and 50 + years of experience repairing them.
He was one of 2 AFA Licensed Aviation Magneto Repair Service people in the USA.
Right in my home area.
He only taught me, no one else.
Come on GUYS, You all want to take me down and Humiliate me..........
Tell you what I am going to do for You............
I will shock myself 1st with my hottest running Vertex Magneto....
I will grab the Vertex magneto cap with my left hand and spin the bronze gear as fast as I can.
Show You I can take the extreme electrical High KV shock Pain.
Then I will hand the magneto to you and let you shock me..........
With my left hand I will grab the magneto cap.
Spin as fast as you can.
I can take it.
Then I will pull a $100 bill out of my pocket and set it on the table.
To earn it 1st, You have to grab the magneto cap with your left of right hand and let me spin it.
I will turn it maybe 1/2 RPM's what You did to me.
I will give you the $100 Bill then to keep.
You earned my respect.
You will earn mine too.
My late buddie and me would take turns shocking each other with those Hot Vertex mags spinning by hand to see he could take it longer.
About a Tie.
About 30 seconds each.
Neither of us Peed our pants.
Sure was fun though seeing who was tougher and crazier.
LOL
Brian
#27
Come on guys.........
Take on my Bet and Dare that I can take extreme pain much longer and better than you can.
A few may believe me.
Convince the other nay Sayers to take on my Vertex Mag Shocking Bet.
One by one.
I will pay.
I am not Chicken............ Are You ?
Brian
Take on my Bet and Dare that I can take extreme pain much longer and better than you can.
A few may believe me.
Convince the other nay Sayers to take on my Vertex Mag Shocking Bet.
One by one.
I will pay.
I am not Chicken............ Are You ?
Brian
#29
Race Director
He was joking about the X-Men movie(s)....with Professor X and Magneto.
http://www.worstpreviews.com/headlin...=20811&count=0
http://www.worstpreviews.com/headlin...=20811&count=0
#30
Race Director
I will shock myself 1st with my hottest running Vertex Magneto....I will grab the Vertex magneto cap with my left hand and spin the bronze gear as fast as I can.
Show You I can take the extreme electrical High KV shock Pain.
Then I will hand the magneto to you and let you shock me..........
Show You I can take the extreme electrical High KV shock Pain.
Then I will hand the magneto to you and let you shock me..........
You're a hoot, Brian!
#31
Pro
#32
Race Director
#33
#34
My little sister lives in Vernon Hills.
Where You are.
She is a Chemical Engineer.
She will testify that I am highly intelligent, a very good mechanic,
I do indeed have that Bad *** 1970-1/2 Trans Am.
She can tell you how fast it pulls from 80-100mph to 160+.
Took my younger brother for a ride too.
He was screaming just as loud as my younger sister.
They both are HARLEY RIDERS and own several of each.
I am the Car nut and fanatic of the family.
Some day you may see me pass through Vernon Hills.
If You want to challenge, let me know.
Otherwise get out the way.
Brian
Brian
Where You are.
She is a Chemical Engineer.
She will testify that I am highly intelligent, a very good mechanic,
I do indeed have that Bad *** 1970-1/2 Trans Am.
She can tell you how fast it pulls from 80-100mph to 160+.
Took my younger brother for a ride too.
He was screaming just as loud as my younger sister.
They both are HARLEY RIDERS and own several of each.
I am the Car nut and fanatic of the family.
Some day you may see me pass through Vernon Hills.
If You want to challenge, let me know.
Otherwise get out the way.
Brian
Brian
#36
Sounds good thanks for calling sorry i had get off phone so quickly but my son had his new girl friend over and they were about to leave for evening. I look foward to pics my email is gassermann@gmail.com thanks for your time Ed
Its a PDF file.
Use the latest version of Adobe reader to open it and view.
Let me know when want me to Service or Hop up a Vertex Mag of yours for street or racing use.
Still an Awesome Ignition System to use as You already know and have found out for yourself.
Vertex mags setup right come alive at 2,000RPM's and don't lay down till at least 10k RPM's.
At least the Mags I blueprint to my specs don't.
Thanks,
Brian R.
#38
#39
I sent out the picture of that Polished-spun Vertex OAC Magneto EMI/RFI magneto cap shield or cover this evening Ed to your email address.
Its a PDF file.
Use the latest version of Adobe reader to open it and view.
Let me know when want me to Service or Hop up a Vertex Mag of yours for street or racing use.
Still an Awesome Ignition System to use as You already know and have found out for yourself.
Vertex mags setup right come alive at 2,000RPM's and don't lay down till at least 10k RPM's.
At least the Mags I blueprint to my specs don't.
Thanks,
Brian R.
Its a PDF file.
Use the latest version of Adobe reader to open it and view.
Let me know when want me to Service or Hop up a Vertex Mag of yours for street or racing use.
Still an Awesome Ignition System to use as You already know and have found out for yourself.
Vertex mags setup right come alive at 2,000RPM's and don't lay down till at least 10k RPM's.
At least the Mags I blueprint to my specs don't.
Thanks,
Brian R.
Sent you a message not usre if it worked but im also after that PDF and pics of that EMI cap.Could you email me at benrx7@bigpond.com
or post that pdf or pics here?
Im a fan of the vertex types of mags.
Breaker points are more raw energy than the electronic points.
Ben