Prices on program chip
Thread Starter
Melting Slicks
Joined: Oct 2001
Posts: 2,320
Likes: 2
From: Salem Oregon
Prices on program chip
I am starting to get the parts to put a engine together and wondered what it would cost to get a chip for it done.
It would be for a 85 with some mods if that makes a difference.
Thanks for any info.
:seeya
It would be for a 85 with some mods if that makes a difference.
Thanks for any info.
:seeya
Team Owner
Joined: Sep 2001
Posts: 62,127
Likes: 1,727
From: Athens AL
C7 of the Year - Unmodified Finalist 2021
C4 of Year Finalist (performance mods) 2019
Re: Prices on program chip (randy814u)
It would be preferable to get an engine builder in your area tune it on a dyno, but if you dont know of any then Ed Wright at Fastchip.com is likely your best bet.
Safety Car
Joined: May 2003
Posts: 4,961
Likes: 2
From: Vette-hid.com Lost in DFW texas
Cruise-In V Veteran
Cruise-In VI Veteran
Cruise-In VII Veteran
St. Jude Donor '06-'07
Re: Prices on program chip (randy814u)
I just got mine from a friend of mine who owns a shop in sanantonio texas
He told me chip prices would be $175 and up depending on how radical you get hemakes wiring harnesses to put the vet motor in annything.He knows his stuff .
he has a gmc sonoma with a 93 vette motor in it and has been written up i many magazines.He is a real good guy answers question and helps whenever he can.
http://www.speedscenewiring.com Ask for zack tell him brian from dallas refered you .
Brian
He told me chip prices would be $175 and up depending on how radical you get hemakes wiring harnesses to put the vet motor in annything.He knows his stuff .
he has a gmc sonoma with a 93 vette motor in it and has been written up i many magazines.He is a real good guy answers question and helps whenever he can.
http://www.speedscenewiring.com Ask for zack tell him brian from dallas refered you .
Brian
Melting Slicks
Joined: Jan 2003
Posts: 2,167
Likes: 0
From: What did the 5 fingers say to the face? SLAP!!
Re: Prices on program chip (randy814u)
Thanks also Ski down it
Jesse is slightly higher than Ed Wright, but he will do unlimited upgrades as you further modify the motor. If I remember right Ed will only upgrade for 6 months. I'm EXTREMELY happy with the chip I got from Jesse
Thread Starter
Melting Slicks
Joined: Oct 2001
Posts: 2,320
Likes: 2
From: Salem Oregon
Re: Prices on program chip (flyersfan1088)
Thanks guys, just the info I was wanting. I have to see what I can afford, then what the wife will let me buy, then there is the--While I am in there stuff.
Thanks again.
:seeya
Thanks again.
:seeya
Safety Car
Joined: May 2003
Posts: 4,961
Likes: 2
From: Vette-hid.com Lost in DFW texas
Cruise-In V Veteran
Cruise-In VI Veteran
Cruise-In VII Veteran
St. Jude Donor '06-'07
Re: Prices on program chip (randy814u)
Zac told me to drive mine and give him feedback so he can do changes
Fuel tranny shift ect.Idont belive he charges for changeing his map and tranny programing.He also loads ecm's that dont have removeable chip via a test bench harness to avoid belowing the ecm.He said he gets alot of people mostly kids with the trans am ect that bumped the cable during load and fried thier computer.He is a great guy full of free info and suggestions.
<P>this is zac sonoma with Lt-1 see sight for complete write up
[Modified by crash1mac, 8:57 PM 5/26/2003]
Fuel tranny shift ect.Idont belive he charges for changeing his map and tranny programing.He also loads ecm's that dont have removeable chip via a test bench harness to avoid belowing the ecm.He said he gets alot of people mostly kids with the trans am ect that bumped the cable during load and fried thier computer.He is a great guy full of free info and suggestions.
<P>this is zac sonoma with Lt-1 see sight for complete write up[Modified by crash1mac, 8:57 PM 5/26/2003]
