Torque convertor not parallel to flexplate
Thread Starter
Melting Slicks
Joined: Oct 2000
Posts: 2,019
Likes: 2
From: Na
Torque convertor not parallel to flexplate
I am a little concerned that after I bolted up my trans to my new 383 the the bottom bolt mount of the TC was not touching the flexplate but the top bolt mount was. It's maybe off by 1/8 of an inch. The trans and converter are the stock units and were untouched when I yanked the engine and trans originally, but the block and flexplate are new to the car. Will everthing line up once I bolt the flexplate to the converter or should they be parellel before bolting them up. What can be causing this miss alignment. Bent flexplate???
Race Director
Joined: Aug 2000
Posts: 14,130
Likes: 7
Cruise-In II Veteran
Re: Torque convertor not parallel to flexplate (NUckINg FuTS)
Did you try pulling on the TC itself to see if it will align up?
Theres a bit of play in it to move back and forth to allow the bolts to align up.
Usually,I would get a bolt started,turn it in halfway,then turn the flexplate/TC over and start and other one until they all went in flush.
This may be what you need to do.Maybe this will help.
Let us know how it makes out.I dont think the flexplate could be bent that bad.Its a sturdy piece itself and would crack before it bent that far.
:cheers:
Theres a bit of play in it to move back and forth to allow the bolts to align up.
Usually,I would get a bolt started,turn it in halfway,then turn the flexplate/TC over and start and other one until they all went in flush.
This may be what you need to do.Maybe this will help.
Let us know how it makes out.I dont think the flexplate could be bent that bad.Its a sturdy piece itself and would crack before it bent that far.
:cheers:
Thread Starter
Melting Slicks
Joined: Oct 2000
Posts: 2,019
Likes: 2
From: Na
Re: Torque convertor not parallel to flexplate (Bill's86Coupe)
Did you try pulling on the TC itself to see if it will align up?
Theres a bit of play in it to move back and forth to allow the bolts to align up.
Usually,I would get a bolt started,turn it in halfway,then turn the flexplate/TC over and start and other one until they all went in flush.
This may be what you need to do.Maybe this will help.
Let us know how it makes out.I dont think the flexplate could be bent that bad.Its a sturdy piece itself and would crack before it bent that far.
:cheers:
Theres a bit of play in it to move back and forth to allow the bolts to align up.
Usually,I would get a bolt started,turn it in halfway,then turn the flexplate/TC over and start and other one until they all went in flush.
This may be what you need to do.Maybe this will help.
Let us know how it makes out.I dont think the flexplate could be bent that bad.Its a sturdy piece itself and would crack before it bent that far.
:cheers:
Race Director
Joined: Sep 2000
Posts: 17,298
Likes: 33
From: The Top of Utah
Re: Torque convertor not parallel to flexplate (NUckINg FuTS)
As I read it, two things have been changed, here. The block and the flexplate. You could pull everything back apart and dial indicate the back of the block and the crank flange, to be sure they are square. You could exchange the flexplate for another, and see if the clearence still exists. OR you could consider the name of the item the converter bolts to. Good luck, and...
RACE ON!!!
[Modified by CFI-EFI, 12:09 PM 10/24/2003]
RACE ON!!!
[Modified by CFI-EFI, 12:09 PM 10/24/2003]
Thread Starter
Melting Slicks
Joined: Oct 2000
Posts: 2,019
Likes: 2
From: Na
Re: Torque convertor not parallel to flexplate (CFI-EFI)
Is it possible I did not reinstall the TC correctly? I did take it off when I pulled the tranny originally. I will try to take pics later on tonight to maybe make things clearer.
Race Director
Joined: Sep 2000
Posts: 17,298
Likes: 33
From: The Top of Utah
Re: Torque convertor not parallel to flexplate (NUckINg FuTS)
Is it possible I did not reinstall the TC correctly?
RACE ON!!!
Thread Starter
Melting Slicks
Joined: Oct 2000
Posts: 2,019
Likes: 2
From: Na
Re: Torque convertor not parallel to flexplate (CFI-EFI)
Is it possible I did not reinstall the TC correctly?
Not to cause the problem you describe. When you install the converter on to the trans, you have to turn it and "jiggle it around. You should hear and feel it click, twice, as it goes on to the trans. Normally, if it isn't on all the way, the flexplate and the converter will interfer before the bellhousing and the block mate up. A correctly installed converter will have to be slid forward to touch the flexplate, once the engine and trans are properly bolted together. I hope my explaination was clear. I'll try again if you don't understand. Good luck, and...
RACE ON!!!
Not to cause the problem you describe. When you install the converter on to the trans, you have to turn it and "jiggle it around. You should hear and feel it click, twice, as it goes on to the trans. Normally, if it isn't on all the way, the flexplate and the converter will interfer before the bellhousing and the block mate up. A correctly installed converter will have to be slid forward to touch the flexplate, once the engine and trans are properly bolted together. I hope my explaination was clear. I'll try again if you don't understand. Good luck, and...
RACE ON!!!
Team Owner
Joined: Mar 2000
Posts: 83,383
Likes: 87
From: Boston, MA
Re: Torque convertor not parallel to flexplate (NUckINg FuTS)
Why not put the 3rd bolt on and then have somebody turn the engine over by hand and monitor the flexplate from underneath? Slap a dial indicator on the side to see if it is outta whack.
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
Every 2027 Corvette Engine Explained
Joe Kucinski
Designer Imagines A Corvette That Looks More Like a Corvette Than the Corvette
Verdad Gallardo
10 Ugly Corvettes That We Still Kinda Love
Joe Kucinski
Top 10 Most Expensive Corvettes Ever Sold on Bring A Trailer
Brett Foote
10 Things Every Corvette Owner Needs (2026 Edition)
Michael S. Palmer
8 Most "Only Corvette Owners Understand" Quirks and Problems
Pouria Savadkouei
10 Reasons the C6 Z06 is Still A Performance Benchmark After 20 Years
Joe Kucinski
How Much Horsepower Every Corvette Engine "LOST" in 1972
Joe Kucinski
