FIKSE FM-5s on !
#4
NCM Lifetime # 982
Love the Fikse's The rear rims look to be a little wider than normal , much better.
#8
Tech Contributor
Thread Starter
Technipolish which is standard. All 17 inch with 315 BFGs on the rear. I believe standard ZR-1 fitment but not positive on the offset. I have a call into Fikse for some new O-Rings. I will ask them to make sure.
Last edited by Goldcylon; 07-07-2009 at 02:58 PM.
#9
Team Owner
Member Since: Jan 2000
Location: Kennesaw, GA www.96LT4.com
Posts: 57,104
Received 64 Likes
on
41 Posts
Former Moderator
Cruise-In II Veteran
Cruise-In III Veteran
Cruise-In IV Veteran
Cruise-In V Veteran
Cruise-In VI Veteran
CI3 Car Show Winner
St. Jude Donor '03-'04-'05-'06-'07-'08-'09-'10-'11-'12-'13-'14-'15-'16-'17-'18-'19-'20-'21
The ones on my Z are 17x9.5 +50mm offset on the front and 17x11 +43mm offset on the rear.
#11
Team Owner
Member Since: Jan 2000
Location: Kennesaw, GA www.96LT4.com
Posts: 57,104
Received 64 Likes
on
41 Posts
Former Moderator
Cruise-In II Veteran
Cruise-In III Veteran
Cruise-In IV Veteran
Cruise-In V Veteran
Cruise-In VI Veteran
CI3 Car Show Winner
St. Jude Donor '03-'04-'05-'06-'07-'08-'09-'10-'11-'12-'13-'14-'15-'16-'17-'18-'19-'20-'21
Fikse told me that I had the "most agressive" stance they offered. Either way, both sets look great!!!
Shot of the rears on the Z:
Shot of the ones on the red LT4...they are "shallower" than the Z rims.
Shot of the rears on the Z:
Shot of the ones on the red LT4...they are "shallower" than the Z rims.
#13
CONGRATS Daryll - Your car sure does look great. Absolutely freaking beautiful.
I must say though, I really think they looked better on Nick's red car.
Please put me first in line for these when you move on and we'll get them back on torch red.
I must say though, I really think they looked better on Nick's red car.
Please put me first in line for these when you move on and we'll get them back on torch red.
#14
Safety Car
Very nice!! Congrats!!
#16
Tech Contributor
Thread Starter
#17
Team Owner
#18
Team Owner
Member Since: Jan 2000
Location: Kennesaw, GA www.96LT4.com
Posts: 57,104
Received 64 Likes
on
41 Posts
Former Moderator
Cruise-In II Veteran
Cruise-In III Veteran
Cruise-In IV Veteran
Cruise-In V Veteran
Cruise-In VI Veteran
CI3 Car Show Winner
St. Jude Donor '03-'04-'05-'06-'07-'08-'09-'10-'11-'12-'13-'14-'15-'16-'17-'18-'19-'20-'21
GC...are you running the stock brakes in the front?
#19
Tech Contributor
Thread Starter
Im running 96 GS/CE Calipers with Baer Eradispeeds. Short answer is yes as there may be clearance issues otherwise for a C5 OR C6 Setup. I know the A-Molds dont have an issue but the sawblades do and the FIKSEs may also have issues of clearance
Last edited by Goldcylon; 07-10-2009 at 09:04 AM.
#20
Team Owner
Member Since: Jan 2000
Location: Kennesaw, GA www.96LT4.com
Posts: 57,104
Received 64 Likes
on
41 Posts
Former Moderator
Cruise-In II Veteran
Cruise-In III Veteran
Cruise-In IV Veteran
Cruise-In V Veteran
Cruise-In VI Veteran
CI3 Car Show Winner
St. Jude Donor '03-'04-'05-'06-'07-'08-'09-'10-'11-'12-'13-'14-'15-'16-'17-'18-'19-'20-'21
Yeah, that's what I'm trying to figure out.
Thanks for the info!
Thanks for the info!