FS: 2003 Z06, Forged LS6 & RPM 60E
#1
2003 Z06, Forged LS6 & RPM 60E $18,000
50,600 miles on the body
Aluminum based ls6
Stock ls6 crank that has been balanced
Scat rods
Mahle pistons
C5R timing set
Manley intake & exhaust valves
PRC 799 heads
Cam motions 235in/ 243ex 637.5 lift @ 111+0 lobe center
.660 BTR spring kit
Yellaterra rockers
Arp rod bolts, head studs, and header studs
Ls6 intake
Stock throttle body
Bosch 42lb injectors
NOS throttle body plate
RPM level 7 60E
Coan 3600 converter
PCS trans controller
QuickTime bellhousing
Misc.
LG super pro headers
B&B bullets
Lg spindles for 15in rears
Aem wideband
Aem fuel pressure gauge
Aem boost controller, and gauge (not needed now)
Nitrous fuel pressure safety switch
Racetronics fuel pump
Alky methonal tank
Nitrous window switch
Bottle heater
17x5 Alumastars
15x10 RTS wheels on drag radials
Speedliine Z06 wheels (factory)
Car was street tuned by Shane Hinds, no dyno numbers and track canceled their last event so I don't have any times. Car runs it's *** off, it has 100hp jets in. I am guessing low 11 car NA and low 10s on spray.
This car is set up very safely for spray.
I'm probably missing things but that's the run down
$20,500 CASH EDITED PRICE (DROPPED)
Only trades i would even remotely consider is 5th/6th gen camaros, V1 & V2, nasty F bodys and would want cash most likely, TBSS, G8GT, possibly older nova, camaro chevelle ect. I'll want to keep my welds most likely unless you have badass wheels also
LOCATED 1.5HRS FROM ST. LOUIS MISSOURI
BUMPED FRONT BUMPER ON CURB last week (2/18/2018) quoted as a $500 job to fix and repaint whole bumper if i disassembled myself.
Aluminum based ls6
Stock ls6 crank that has been balanced
Scat rods
Mahle pistons
C5R timing set
Manley intake & exhaust valves
PRC 799 heads
Cam motions 235in/ 243ex 637.5 lift @ 111+0 lobe center
.660 BTR spring kit
Yellaterra rockers
Arp rod bolts, head studs, and header studs
Ls6 intake
Stock throttle body
Bosch 42lb injectors
NOS throttle body plate
RPM level 7 60E
Coan 3600 converter
PCS trans controller
QuickTime bellhousing
Misc.
LG super pro headers
B&B bullets
Lg spindles for 15in rears
Aem wideband
Aem fuel pressure gauge
Aem boost controller, and gauge (not needed now)
Nitrous fuel pressure safety switch
Racetronics fuel pump
Alky methonal tank
Nitrous window switch
Bottle heater
17x5 Alumastars
15x10 RTS wheels on drag radials
Speedliine Z06 wheels (factory)
Car was street tuned by Shane Hinds, no dyno numbers and track canceled their last event so I don't have any times. Car runs it's *** off, it has 100hp jets in. I am guessing low 11 car NA and low 10s on spray.
This car is set up very safely for spray.
I'm probably missing things but that's the run down
$20,500 CASH EDITED PRICE (DROPPED)
Only trades i would even remotely consider is 5th/6th gen camaros, V1 & V2, nasty F bodys and would want cash most likely, TBSS, G8GT, possibly older nova, camaro chevelle ect. I'll want to keep my welds most likely unless you have badass wheels also
LOCATED 1.5HRS FROM ST. LOUIS MISSOURI
BUMPED FRONT BUMPER ON CURB last week (2/18/2018) quoted as a $500 job to fix and repaint whole bumper if i disassembled myself.
Last edited by nightmareC5; 07-22-2018 at 11:51 PM.
The following users liked this post:
CorvetteBrent (07-26-2018)
The following users liked this post:
CorvetteBrent (07-26-2018)
#10
Nice grudge car
#12
The following users liked this post:
CorvetteBrent (07-26-2018)
#15
#18
The following users liked this post:
CorvetteBrent (07-26-2018)