Belt Alignment Problem
Thread Starter
Pro
Joined: Dec 2000
Posts: 690
Likes: 202
From: Hoffman Estates, IL
Belt Alignment Problem
I have a Carroll Supercharging setup that uses the Vortech headunit mounted on the passenger side. I'm having some moderate belt shredding issues that I know are related to poor pulley alignment. I have a ton of rubber dust all over the front of my pulleys, mostly around the tensioner pulley. The inner most rib is gone, and when I track the car I will lose another 2 or 3 ribs.
I did a forum search and found this is a common problem, and everyone suggests using a laser tool to align the pulleys. My question is how to do this?
So I just go to Home Depot and buy a laser leveler and then what? Hold it up against a pulley and put it in line with a rib on one pulley and see if it lines up? How do you mount or fix the laser tool to something rigid? (I assume you can't just hold it in your hand because the laser line will wobble).
I just need a little explaining. Thanks.
I did a forum search and found this is a common problem, and everyone suggests using a laser tool to align the pulleys. My question is how to do this?
So I just go to Home Depot and buy a laser leveler and then what? Hold it up against a pulley and put it in line with a rib on one pulley and see if it lines up? How do you mount or fix the laser tool to something rigid? (I assume you can't just hold it in your hand because the laser line will wobble).
I just need a little explaining. Thanks.
Thread Starter
Pro
Joined: Dec 2000
Posts: 690
Likes: 202
From: Hoffman Estates, IL
Thanks Mark, that is exactly the info I was looking for. I called my local Gates vendor and it lists for $323 
, but they'll sell it to me for $199. 
Whatever... still pricey.
Since this seems to be such a common problem in this forum, I think it would be no problem selling to another forum member for a little less after I fix my problems. Or maybe I could start a "Rent-A-BlowerBeltAlignment-Tool" website. $25 for a week.
Thx for the info.
-Jacob
, but they'll sell it to me for $199. Whatever... still pricey.Since this seems to be such a common problem in this forum, I think it would be no problem selling to another forum member for a little less after I fix my problems. Or maybe I could start a "Rent-A-BlowerBeltAlignment-Tool" website. $25 for a week.
Thx for the info.
-Jacob
Originally Posted by mdhmi
The following is a picture of the Gates Laser Alignment tool.
You'll notice that the tool rests on the pulley..
Good Luck,
Mark
You'll notice that the tool rests on the pulley..
Good Luck,
Mark
Team Owner
Joined: Jul 2003
Posts: 20,474
Likes: 2
From: Detroit
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
Top 10 Most Expensive Corvettes Ever Sold on Bring A Trailer
Brett Foote
10 Things Every Corvette Owner Needs (2026 Edition)
Michael S. Palmer
8 Most "Only Corvette Owners Understand" Quirks and Problems
Pouria Savadkouei
10 Reasons the C6 Z06 is Still A Performance Benchmark After 20 Years
Joe Kucinski
How Much Horsepower Every Corvette Engine "LOST" in 1972
Joe Kucinski
Top 10 DOs and DON'Ts for Protecting Your Convertible Top!
Michael S. Palmer
Top 10 Most Explosive Corvettes Ever Made: Power-to-Weight Ratio Ranked!
Joe Kucinski
150 hp to 1,250 hp: Every Corvette Generation Compared by the Specs That Matter
Joe Kucinski
8 Coolest Corvette Pace Cars (and Replicas) of All Time
Verdad Gallardo
Thread Starter
Pro
Joined: Dec 2000
Posts: 690
Likes: 202
From: Hoffman Estates, IL
Now you tell me!! 
Originally Posted by mdhmi
Race Director
Joined: Jan 2003
Posts: 19,802
Likes: 0
From: San Antonio Texas
St. Jude Donor '05-'06-'08
Belt Alignment
I had some alignment problems few months ago.....I notoced after installing D1SC I had lots of belt dust........Now, its perfect and even went to the track and no dust. My belt was jumping 1 or 2 grooves as well.
Thanks to Arnold (gotjuiced?) they are perfect, he aligned them for me!
By the way, that is an awsome alignment tool.....a must for the tool box!
Thanks to Arnold (gotjuiced?) they are perfect, he aligned them for me!
By the way, that is an awsome alignment tool.....a must for the tool box!
