500-525rwhp depending on boost level and how hard you want to push it..
Maggie power question
Thread Starter
Pro
Joined: Nov 2002
Posts: 722
Likes: 0
From: ********************* Florida's Space Coast *********************
Maggie power question
I have a few questions about adding a maggie to my current setup.
I would be pulling my DP but leaving everything else listed in my sig. I am currently making around 415 rwhp (off the juice) and would like to know where I would end up with a maggie/intercooler system with my cam/headers/Vararam. Can I expect an additional 130 rwhp like they advertise or am I looking at a much lower number. Basically I want to know if I would be around 550 rwhp or closer to 500 with what I have?
Any real world rwhp numbers on a Z06 would also be great along with 1/4 times if available.
I am not looking for 10.0 car, but in the 10's without turning on a bottle would be nice...
I would be pulling my DP but leaving everything else listed in my sig. I am currently making around 415 rwhp (off the juice) and would like to know where I would end up with a maggie/intercooler system with my cam/headers/Vararam. Can I expect an additional 130 rwhp like they advertise or am I looking at a much lower number. Basically I want to know if I would be around 550 rwhp or closer to 500 with what I have?
Any real world rwhp numbers on a Z06 would also be great along with 1/4 times if available.
I am not looking for 10.0 car, but in the 10's without turning on a bottle would be nice...
Melting Slicks
Joined: Sep 2004
Posts: 3,178
Likes: 13
From: N. County/San Diego
Depends on boost, being that you have a Z06 you need to be a little more careful than an LS1 due to higher compresion.
With your existing set-up and the standard Maggie pully I`d say around 525-535rwhp.
With your existing set-up and the standard Maggie pully I`d say around 525-535rwhp.
Drifting
Joined: Dec 1999
Posts: 1,541
Likes: 2
From: Raleigh NC
What size pulley are you guys running. I just did my install with a 3.1 on my Z. The power and response is amazing. I am also using ECS's alky kit. During my tuning run there was no knock and I'm running quite a bit of timing. AFR's are around 11.8.
Thread Starter
Pro
Joined: Nov 2002
Posts: 722
Likes: 0
From: ********************* Florida's Space Coast *********************
Thanks everyone. Still would love to see some 1/4 times if anyone has them.
Looks like I may go the KB route. The maggie looks better IMHO, but the KB seems to have the edge on power and when I go forged I can up the boost a little easier on it.
Thanks again.... Stay tuned.
Looks like I may go the KB route. The maggie looks better IMHO, but the KB seems to have the edge on power and when I go forged I can up the boost a little easier on it.
Thanks again.... Stay tuned.
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
Top 10 Most Expensive Corvettes Ever Sold on Bring A Trailer
Brett Foote
10 Things Every Corvette Owner Needs (2026 Edition)
Michael S. Palmer
8 Most "Only Corvette Owners Understand" Quirks and Problems
Pouria Savadkouei
10 Reasons the C6 Z06 is Still A Performance Benchmark After 20 Years
Joe Kucinski
How Much Horsepower Every Corvette Engine "LOST" in 1972
Joe Kucinski
Top 10 DOs and DON'Ts for Protecting Your Convertible Top!
Michael S. Palmer
Top 10 Most Explosive Corvettes Ever Made: Power-to-Weight Ratio Ranked!
Joe Kucinski
150 hp to 1,250 hp: Every Corvette Generation Compared by the Specs That Matter
Joe Kucinski
8 Coolest Corvette Pace Cars (and Replicas) of All Time
Verdad Gallardo
Le Mans Master
Joined: Aug 2001
Posts: 6,725
Likes: 5
From: Colesville MD
My Maggie is currently for sale.
http://forums.corvetteforum.com/show....php?t=1616806