Robert
Thoughts?
Thread Starter
Drifting
Joined: Aug 2009
Posts: 1,828
Likes: 14
Thoughts?
Getting ready to finish the build.
Will be putting in a new motor and here is where I am: Thoughts and/or suggestions - RWHP ??
427 RHS Aluminum Block
Collies Dragon Slayer Forged Crankshaft
Wesco Forged Aluminum Pistons
427 Turbo Comp Custom Cam
STS Twin Turbos
LSXR LS7 Cylinder Heads
T&D Rocker Arms Intake & Exhaust
Manly Push Rods
Wilson Billet Banks Sheet Metal Intake Machined for Automotive Fuel Rails
Callies Ultra Billet H Beam Connecting Rods
Clevite H Main & Rod Bearings
C5R Timing Chain
Morel Tie Bar Hi RPM Hyd Roller Lifter
T&D Rocker Arms -Intake and Exhaust
Cometic Head Gaskets
LS2 Front Timing Cover W/Cam Sensor
APR Pro Series 12 pt. Head studs LSX 6 bolt confriguration
APR Balance Bolt
Patriot Perf Extreme Valve Spring Upgrade Kit
High Volue LSX Ported Oil Pump
Balanced & Blueprinted Rotating Assembly
LSX Engine Gasket Kit
Manley Push Rods
Will be putting in a new motor and here is where I am: Thoughts and/or suggestions - RWHP ??
427 RHS Aluminum Block
Collies Dragon Slayer Forged Crankshaft
Wesco Forged Aluminum Pistons
427 Turbo Comp Custom Cam
STS Twin Turbos
LSXR LS7 Cylinder Heads
T&D Rocker Arms Intake & Exhaust
Manly Push Rods
Wilson Billet Banks Sheet Metal Intake Machined for Automotive Fuel Rails
Callies Ultra Billet H Beam Connecting Rods
Clevite H Main & Rod Bearings
C5R Timing Chain
Morel Tie Bar Hi RPM Hyd Roller Lifter
T&D Rocker Arms -Intake and Exhaust
Cometic Head Gaskets
LS2 Front Timing Cover W/Cam Sensor
APR Pro Series 12 pt. Head studs LSX 6 bolt confriguration
APR Balance Bolt
Patriot Perf Extreme Valve Spring Upgrade Kit
High Volue LSX Ported Oil Pump
Balanced & Blueprinted Rotating Assembly
LSX Engine Gasket Kit
Manley Push Rods
Tech Contributor
Joined: Apr 2007
Posts: 10,924
Likes: 78
From: Forney Texas
If you have the time, I recommend hard anodizing the pistons. It makes them bullet proof!
The Wilson manifold looks wicked, but unless you're doing it to have a baller look and don't care about spending the money, there's absolutely no need for it. It won't help your power one lick.
Not sure what your power goals are, but the I-beam Ultra billet rods are significantly stronger.
The Wilson manifold looks wicked, but unless you're doing it to have a baller look and don't care about spending the money, there's absolutely no need for it. It won't help your power one lick.
Not sure what your power goals are, but the I-beam Ultra billet rods are significantly stronger.
Melting Slicks
Joined: Mar 2005
Posts: 2,225
Likes: 42
From: Okinawa
Is this build almost done, or are you still buying parts/getting started. Are you trying to go fast? An RHS block and sts dont go together, lsxr heads and patriot springs? C5R timming chain? I hope its not to late to make some changes. Is a shop doing this for you?
Former Vendor
Joined: Jul 2010
Posts: 4,504
Likes: 4
From: Waterloo Ontario
Team Owner
Joined: Jan 2007
Posts: 29,063
Likes: 1,839
From: cookeville tennessee
Melting Slicks
Joined: Mar 2005
Posts: 2,225
Likes: 42
From: Okinawa
No need to buy an after market block for an sts kit or one that is lightly modded, if you spend the money for a rhs block I would spend more on a timming chain. Lxr heads probably come with better springs....
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
Top 10 Most Expensive Corvettes Ever Sold on Bring A Trailer
Brett Foote
10 Things Every Corvette Owner Needs (2026 Edition)
Michael S. Palmer
8 Most "Only Corvette Owners Understand" Quirks and Problems
Pouria Savadkouei
10 Reasons the C6 Z06 is Still A Performance Benchmark After 20 Years
Joe Kucinski
How Much Horsepower Every Corvette Engine "LOST" in 1972
Joe Kucinski
Top 10 DOs and DON'Ts for Protecting Your Convertible Top!
Michael S. Palmer
Top 10 Most Explosive Corvettes Ever Made: Power-to-Weight Ratio Ranked!
Joe Kucinski
150 hp to 1,250 hp: Every Corvette Generation Compared by the Specs That Matter
Joe Kucinski
8 Coolest Corvette Pace Cars (and Replicas) of All Time
Verdad Gallardo
Race Director
Joined: May 2003
Posts: 12,725
Likes: 14
From: ECS : WTF did you break now and HTF did you break it this time
my forged 346 car with STS couldn't run a number on the dyno and absolutely on the track....after I switched to a paxton I couldn't keep a happy driveline behind it.
I would seriously, seriously rethink plans of STS and big power, it WILL NOT happen.
I sold mine off over 4 years ago, we tried bigger turbos, ceramic coatings, heat wrapping, removing cats etc. you name it, we just couldn't make a design with 20 ft of charge pipes spool like a front mount or a centrifugal.
As a result I went paxton..
PS let me know if you want a deal on a paxton setup, I just pulled that from this car to sell it stock, going back NA 427 C5R with a bottle for when I want to be stupid
I would seriously, seriously rethink plans of STS and big power, it WILL NOT happen.
I sold mine off over 4 years ago, we tried bigger turbos, ceramic coatings, heat wrapping, removing cats etc. you name it, we just couldn't make a design with 20 ft of charge pipes spool like a front mount or a centrifugal.
As a result I went paxton..
PS let me know if you want a deal on a paxton setup, I just pulled that from this car to sell it stock, going back NA 427 C5R with a bottle for when I want to be stupid
