[Z06] Special deal, Vette Tray and Z06 Partition
#1
Supporting Vendor
Thread Starter
Member Since: Jun 2005
Location: Marietta Georgia
Posts: 20,644
Received 315 Likes
on
288 Posts
St. Jude Donor '06-'07, '13, '15
Special deal, Vette Tray and Z06 Partition
If you are looking for a storage/rear organizer solution for your C5 Z06, the Vette Tray and Partition Combo is the answer...
The C5 Corvette Z06-FRC Trunk Partition and matching VetteTray Cargo Organizer separate the passenger compartment from the trunk, reduces road noise, increase AC effectiveness, improves stereo sound by reducing acoustic mass, and also provides convenient storage for cell phones, sunglasses, wallets and any other small items that might be sloshing around in your rear area.
- Easily installs with NO MODIFICATIONS to your car
- Does not come loose under hard braking or acceleration
- Comes in Black Carpet for a perfect fit and finish
Does NOT need to be removed for access to your center storage compartment.
Both the C5 Z06 Partition and Vette Tray are included in this package deal with Free Shipping.
Click below for ordering information....
Corvette C5 Z06 Partition and Vette Tray Package Deal
The C5 Corvette Z06-FRC Trunk Partition and matching VetteTray Cargo Organizer separate the passenger compartment from the trunk, reduces road noise, increase AC effectiveness, improves stereo sound by reducing acoustic mass, and also provides convenient storage for cell phones, sunglasses, wallets and any other small items that might be sloshing around in your rear area.
- Easily installs with NO MODIFICATIONS to your car
- Does not come loose under hard braking or acceleration
- Comes in Black Carpet for a perfect fit and finish
Does NOT need to be removed for access to your center storage compartment.
Both the C5 Z06 Partition and Vette Tray are included in this package deal with Free Shipping.
Click below for ordering information....
Corvette C5 Z06 Partition and Vette Tray Package Deal
__________________
Last edited by southerncarparts; 09-03-2019 at 11:17 AM.
#6
Supporting Vendor
Thread Starter
Member Since: Jun 2005
Location: Marietta Georgia
Posts: 20,644
Received 315 Likes
on
288 Posts
St. Jude Donor '06-'07, '13, '15
Originally Posted by Jay 383
I wish I'd have known about the red lid covers! That looks nice.
Here are some pics from my car with them in place.
Two thumbs up!
Here are some pics from my car with them in place.
Two thumbs up!
Jim
#8
Supporting Vendor
Thread Starter
Member Since: Jun 2005
Location: Marietta Georgia
Posts: 20,644
Received 315 Likes
on
288 Posts
St. Jude Donor '06-'07, '13, '15
Originally Posted by jgmachine
any way to get them leather wrapped?
Are you sure you would not be happy with carpet? Leather would be a nightmare to make.
Wish I could, but would be cost prohibitive.
See ya,
Jim
Last edited by southerncarparts; 10-23-2005 at 09:39 PM. Reason: Spelling
#10
Supporting Vendor
Thread Starter
Member Since: Jun 2005
Location: Marietta Georgia
Posts: 20,644
Received 315 Likes
on
288 Posts
St. Jude Donor '06-'07, '13, '15
Originally Posted by SLO VETTE
how do the lids stay on there? velcro? is there a hinge of some sort?
thanks!
thanks!
Jim
#11
Race Director
Originally Posted by southerncarparts
1 more combo ready to ship...$240 takes it shipped to your door.
Partition and Vette Tray with lids....
Jim
Partition and Vette Tray with lids....
Jim
Thanks George
#12
Supporting Vendor
Thread Starter
Member Since: Jun 2005
Location: Marietta Georgia
Posts: 20,644
Received 315 Likes
on
288 Posts
St. Jude Donor '06-'07, '13, '15
Originally Posted by GeorgeZNJ
hey Jim, check sent for combo,PMed price black, Z06 logo, (02Z06)
Thanks George
Thanks George
Wonderful...I will have everything ready to ship as soon as the check arrives.
See ya,
Jim
#14
Supporting Vendor
Thread Starter
Member Since: Jun 2005
Location: Marietta Georgia
Posts: 20,644
Received 315 Likes
on
288 Posts
St. Jude Donor '06-'07, '13, '15
We could make something that goes from the front lip back to the edge of of the roll bar. You would end up with a (what looks like) 1 inch gap from the roll bar back to the partition. I think it would look good. What is the exact measurements from the lip back to the leading edge of the roll bar?
Jim
Jim
#17
Le Mans Master
Member Since: Aug 1999
Location: N Carolina 08 Z51 Coupe
Posts: 5,411
Likes: 0
Received 1 Like
on
1 Post
I do want a partition and these look very nice...
I just keep thinking about all the trouble GM went to keep the weight down in these cars... I mean even the windshield uses thinner glass to keep every ounce down to a minimum...
So I just don't feel comfortable adding 12 or 18 pounds for a non oem, non performance part...
I think I might opt for the all foam one... it works and weighs almost nothing...
Maybe I'm being too ****...
I just keep thinking about all the trouble GM went to keep the weight down in these cars... I mean even the windshield uses thinner glass to keep every ounce down to a minimum...
So I just don't feel comfortable adding 12 or 18 pounds for a non oem, non performance part...
I think I might opt for the all foam one... it works and weighs almost nothing...
Maybe I'm being too ****...
#18
Supporting Vendor
Thread Starter
Member Since: Jun 2005
Location: Marietta Georgia
Posts: 20,644
Received 315 Likes
on
288 Posts
St. Jude Donor '06-'07, '13, '15
Originally Posted by C5~Missle
I do want a partition and these look very nice...
I just keep thinking about all the trouble GM went to keep the weight down in these cars... I mean even the windshield uses thinner glass to keep every ounce down to a minimum...
So I just don't feel comfortable adding 12 or 18 pounds for a non oem, non performance part...
I think I might opt for the all foam one... it works and weighs almost nothing...
Maybe I'm being too ****...
I just keep thinking about all the trouble GM went to keep the weight down in these cars... I mean even the windshield uses thinner glass to keep every ounce down to a minimum...
So I just don't feel comfortable adding 12 or 18 pounds for a non oem, non performance part...
I think I might opt for the all foam one... it works and weighs almost nothing...
Maybe I'm being too ****...
Both the Partition and Tray are friction fit and are easily removed if you are heading for the track and need to be concience of weight.
$240.00 Shipped for both the VetteTray and a matching Trunk Partition!
Check it out, you won't be dissapointed.
Jim
#19
Heel & Toe
Member Since: May 2005
Location: Suisun city California
Posts: 24
Likes: 0
Received 0 Likes
on
0 Posts
hey jim,
Im very interested in the partition/tray combo, but i am currently deployed to Iraq until late Feb. and wanted to know how i can order and ship it. thanks
rob
Im very interested in the partition/tray combo, but i am currently deployed to Iraq until late Feb. and wanted to know how i can order and ship it. thanks
rob
#20
Supporting Vendor
Thread Starter
Member Since: Jun 2005
Location: Marietta Georgia
Posts: 20,644
Received 315 Likes
on
288 Posts
St. Jude Donor '06-'07, '13, '15
Originally Posted by 347_C.I.D.
hey jim,
Im very interested in the partition/tray combo, but i am currently deployed to Iraq until late Feb. and wanted to know how i can order and ship it. thanks
rob
Im very interested in the partition/tray combo, but i am currently deployed to Iraq until late Feb. and wanted to know how i can order and ship it. thanks
rob
See ya,
Jim