Code help wanted
Thread Starter
Drifting
Joined: May 2007
Posts: 1,409
Likes: 110
From: Chandler AZ
Code help wanted
Just returned from the body shop, slight rear quarter panel repair.
Check Engine light is continuosly on. Have checked all the obvious, gas cap and cleaned filler area. Also cleaned out "body shop dust" from engine area with compressed air.
After completing the procedure of key on, press reset, press & hold options & then fuel 4 times what I end up with on the display is:
"10 PCM 1 codes", where do I go from here? If I need to go to another step to identify a code, how do I do it?????
Thanks anyone..........
Check Engine light is continuosly on. Have checked all the obvious, gas cap and cleaned filler area. Also cleaned out "body shop dust" from engine area with compressed air.
After completing the procedure of key on, press reset, press & hold options & then fuel 4 times what I end up with on the display is:
"10 PCM 1 codes", where do I go from here? If I need to go to another step to identify a code, how do I do it?????
Thanks anyone..........
Le Mans Master
Joined: May 2007
Posts: 5,383
Likes: 6
From: hagerstown md
St. Jude Donor '08-'09
Once you pull up the diagnostics on your DIC, you let them scroll by them selves and they will go through the whole cycle. PCM, RADIO, HVAC, etc...write down what codes you find after each segment, and whether or not they have an H or a C behind the numbers. Post what codes you have, then you can get a better answer. Here's a link to help you get and diagnose the codes. 
http://www.corvettedoctor.com/2004_DTC_Codes.html
http://www.corvettedoctor.com/2004_DTC_Codes.html
Thread Starter
Drifting
Joined: May 2007
Posts: 1,409
Likes: 110
From: Chandler AZ
Ran the cycle again and all codes that appeared were with an H, no C's anywhere.
After the DIC displays "no more codes" it then goes to "manual diagnostics" then the 10-PCM 1 codes appears on the display?????
I cannot get anything else to appear and the engine light stays on !!
After the DIC displays "no more codes" it then goes to "manual diagnostics" then the 10-PCM 1 codes appears on the display?????
I cannot get anything else to appear and the engine light stays on !!
Le Mans Master
Joined: May 2007
Posts: 5,383
Likes: 6
From: hagerstown md
St. Jude Donor '08-'09
Once you get to manual diagnostics, push the options button, or one of the other buttons(do not push the E/M button that cancels diagnostics). You should be able to cycle through the diagnostics. Once you move from one section to the next and it shows the codes for that section push and hold the reset button until it says no codes. Then move on to the next section, until all codes are clear. You should be able to clear them all this way.
Check your PM's.
Check your PM's.
Last edited by sneakelman; Dec 6, 2007 at 09:31 PM.
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
8 Coolest Corvette Pace Cars (and Replicas) of All Time
Verdad Gallardo
Top 10 Corvette Engines RANKED by Peak Torque (70+ Years of Muscle!)
Joe Kucinski
Corvette ZR1X Will Be Pacing the Indy 500, And Could Probably Race, Too!
Verdad Gallardo
Top 10 Corvettes Coming to Mecum Indy 2026!
Brett Foote
Top 10 C9 Corvette MUST-HAVES to Fix These C8 Generation Flaws!
Michael S. Palmer
10 Revolutionary 'Corvette Firsts' Most People Don't Know
Joe Kucinski
5 Reasons to Upgrade to an LS6-Powered Corvette; 5 Reasons to Stay LT2
Michael S. Palmer
2027 Corvette vs The World: Every C8 vs Its Closest Competitor
Joe Kucinski