[Z06] LG Motorsports Carbon XR Install
#41
#42
Le Mans Master
I don't know a single cop (and I know HUNDREDS because I was a cop for 15 years) who would bother issuing a citation for a mod like wipers, on a car like a ZO6, when the guy could just swap everything back over to OEM in 3 hours and go to court. Waste of time for us man. Plus, how cool is a built vette?
#43
Premium Supporting Vendor
Thread Starter
http://www.torquerush.com/x2.html
It'll be a custom cold air setup
I don't know a single cop (and I know HUNDREDS because I was a cop for 15 years) who would bother issuing a citation for a mod like wipers, on a car like a ZO6, when the guy could just swap everything back over to OEM in 3 hours and go to court. Waste of time for us man. Plus, how cool is a built vette?
Last edited by Fernando@LGMotorsports; 01-21-2019 at 11:57 AM.
#44
I don't know a single cop (and I know HUNDREDS because I was a cop for 15 years) who would bother issuing a citation for a mod like wipers, on a car like a ZO6, when the guy could just swap everything back over to OEM in 3 hours and go to court. Waste of time for us man. Plus, how cool is a built vette?
#46
Le Mans Master
I DEMAND an update!!!
#47
Premium Supporting Vendor
Thread Starter
The following 2 users liked this post by Fernando@LGMotorsports:
1stls7 (10-05-2019),
Pb82 Ronin (01-22-2019)
#48
Le Mans Master
Is it bolted down? CAI designed yet? Hood cuts?
EDIT: I know, patience right? Most intakes I would cringe at chopping up my hood for. This intake I would be happy to break out the cutoff wheel and display proudly. Still eager to see the finished result.
EDIT: I know, patience right? Most intakes I would cringe at chopping up my hood for. This intake I would be happy to break out the cutoff wheel and display proudly. Still eager to see the finished result.
Last edited by Pb82 Ronin; 01-23-2019 at 06:57 AM.
#49
Melting Slicks
Fernando - if you could redesign the back on the drivers side how much would you need to cut and reshape the back part so not to mess with the windshield wipers. I realize it may look a little weird and there may be a little less in the plenum (but back there it is kind of dead space). I am guessing but say 1-2 inches. You would need to move the little sensor hole up but there is plenty of room. Another idea would be to slant the underside of the back a little. That way it looks OK but misses the windshield wipers by them being underneath. The reason I say this is maybe the manufacturer is watching this build or should be and they could figure a way to make it work. Still have to do some cutting but maybe make it a little more user friendly and thus generate some more sales for the company. Of course this would be predicated on you producing some big HP/TQ gains here over whatever was on there before.
Last edited by double06; 01-23-2019 at 08:12 AM. Reason: adding stuff
#50
Race Director
Member Since: Mar 2006
Location: Everywhere and Nowhere at all
Posts: 15,357
Received 1,679 Likes
on
1,135 Posts
its extremely cool. Especially when it’s done right and you live somewhere that doesn’t have built vettes. I’ve been stop twice by cops for simple ****, a California roll and no blinker I think.....but the main reason they pulled me over was to check out the car, I knew instantly when they walked up I wasn’t getting a ticket and it was an “excuse” to shoot the **** about the car and get a better look. Which for me was cool cause if I’m driving the vette it’s a nice day and I probably have no where to be anyway lol. Keep in mind my windows are 5% too. I also wasn’t do anything that would be frowned upon either.....that’s makes all the difference with the boys in blue....at least from my experience.
The following users liked this post:
jayyyw (01-23-2019)
#51
Premium Supporting Vendor
Thread Starter
Fernando - if you could redesign the back on the drivers side how much would you need to cut and reshape the back part so not to mess with the windshield wipers. I realize it may look a little weird and there may be a little less in the plenum (but back there it is kind of dead space). I am guessing but say 1-2 inches. You would need to move the little sensor hole up but there is plenty of room. Another idea would be to slant the underside of the back a little. That way it looks OK but misses the windshield wipers by them being underneath. The reason I say this is maybe the manufacturer is watching this build or should be and they could figure a way to make it work. Still have to do some cutting but maybe make it a little more user friendly and thus generate some more sales for the company. Of course this would be predicated on you producing some big HP/TQ gains here over whatever was on there before.
Last edited by Fernando@LGMotorsports; 01-23-2019 at 05:16 PM.
#52
i was curious to how close it really was to the glass.
really surprised it had that much space from the other images.
really surprised it had that much space from the other images.
Last edited by jammeejamm; 01-23-2019 at 11:58 PM.
#53
Le Mans Master
Are the motor mounts stock in that car?
#54
How much power are you expected to gain with this intake
#55
Melting Slicks
I thin somewhere they said like 40-50 hp. But not sure what that is over (stock, fast, MSD). They have some dyno sheets on the Carbon XR website with like a 650 flywheel hp motor I think.
#57
Le Mans Master
Please.....must......update!!
#58
Team Owner
#59
Le Mans Master
Anyone?
#60
Premium Supporting Vendor
Thread Starter
We're still playing with the clocking of the pipes but it's more or less finished
Mods:
LG G7X3 Cam
Carbon XR Intake
ID1050 Injectors
2" Headers - probably hurting his power band right now
It's on the dyno right now. I'll have numbers soon
Fernando
Mods:
LG G7X3 Cam
Carbon XR Intake
ID1050 Injectors
2" Headers - probably hurting his power band right now
It's on the dyno right now. I'll have numbers soon
Fernando