Let's see some aftermarket valve covers
04-06-2016, 06:05 PM
#1
Let's see some aftermarket valve covers
Doesn't matter if they're yours or not as long as they'll fit on a LS head. What's everyone's favorite valve covers?
Last edited by usmcpony; 04-06-2016 at 06:06 PM.
The following users liked this post:
Slo-Poc (04-20-2016)
04-07-2016, 01:58 AM
#6
Race Director
Member Since: Dec 2010
Location: Atlanta, GA
Posts: 10,426
Received 1,261 Likes
on
1,056 Posts
2020 Corvette of the Year Finalist (performance mods)
C5 of Year Winner (performance mods) 2019
GMPP
The following users liked this post:
ajrothm (04-07-2016)
The following users liked this post:
neutron82 (04-07-2016)
04-07-2016, 02:31 AM
#9
Race Director
Member Since: Dec 2010
Location: Atlanta, GA
Posts: 10,426
Received 1,261 Likes
on
1,056 Posts
2020 Corvette of the Year Finalist (performance mods)
C5 of Year Winner (performance mods) 2019
The following users liked this post:
neutron82 (04-07-2016)
04-07-2016, 05:10 AM
#11
04-07-2016, 09:16 AM
#12
Race Director
Member Since: Dec 2010
Location: Atlanta, GA
Posts: 10,426
Received 1,261 Likes
on
1,056 Posts
2020 Corvette of the Year Finalist (performance mods)
C5 of Year Winner (performance mods) 2019
04-07-2016, 09:57 AM
#13
Le Mans Master
More Proforms here.
But it will look much better when I get it back together now with AN's for crankcase breathing and wrinkle black.
But it will look much better when I get it back together now with AN's for crankcase breathing and wrinkle black.
04-07-2016, 01:55 PM
#14
Le Mans Master
Make sure to use some wires with the lowest Ohms that you can get.... If not, you'll run into misfiring issues under boost... The coils are just not strong enough to light it since they are over 3' away...so any additional resistance will add to the problem.
I used MSD super conductors for years, now I run the Taylor 25 ohm race wire and like it MUCH better. Taylor plug ends are 10x better then MSD.
Last edited by ajrothm; 04-07-2016 at 01:56 PM.
The following users liked this post:
speedz06 (04-23-2016)
04-07-2016, 03:21 PM
#16
Le Mans Master
They're pretty neat and the price point is nice. Only drawback is they don't take an LS oil cap. You have to use a SBC style one which is why I have that big ugly breather on one of my pics. Now I just fill through the AN. Also the rubber washers around the bolts get soft and start squishing out. Replace with nylon washers from the hardware store and all good.
Last edited by 5 Liter Eater; 04-07-2016 at 11:43 PM.
04-08-2016, 10:55 AM
#19
Race Director
Member Since: Dec 2010
Location: Atlanta, GA
Posts: 10,426
Received 1,261 Likes
on
1,056 Posts
2020 Corvette of the Year Finalist (performance mods)
C5 of Year Winner (performance mods) 2019
04-08-2016, 11:38 AM
#20
Race Director
Member Since: May 2004
Location: Raleigh, NC
Posts: 16,664
Received 1,195 Likes
on
1,053 Posts
St. Jude Donor '15
I had that happen on the seat heater connector on my truck. The thing was melted.. common problem too. I replaced all the pins and connectors and it's been fine ever since, fortunately.