Eliminator stealth corvette fuel system
#1
Pro
Thread Starter
Member Since: Dec 2010
Location: Davie Florida
Posts: 554
Likes: 0
Received 0 Likes
on
0 Posts
Eliminator stealth corvette fuel system
Eliminator Corvette Stealth fuel system
pump
18671 - Eliminator Corvette Stealth Kit
Fits 2003 1/2 and later Corvettes (Late C5 and C6)
• Supports up to 1900 HP – naturally aspirated
• Supports up to 1400 HP – forced air induction
• ORB-08 outlet port
• ORB-06 return port
• Incorporates factory jet siphon system and sending unit
• Includes an integrated 100-Micron Stainless Steel pre-pump filter
• Utilizes the factory tank, o-ring, lock ring and mounting location
• Includes all necessary fittings and hardware to plumb the pump into your tank
Aeromotive 16306 - Aeromotive Billet Electric Fuel Pump Controllers
Aeromotive 13105 - Compact EFI Regulator
lines
-8 single feed to a Y block by the firewall to both ends of aftermarket rails.
-6 return to regulator to pump
all lines are PTFE Teflon hose so no fuel smell when you park your car in the garage and prolong life of the hose.
into on PTFE http://www.hotrod.com/techarticles/e...ce_fuel_hoses/
Comes with pump, lines, regulator, filter, check valve, fittings for aftermarket rails, and fuel pump controller
The pump replaces the stock unit, reuse your fuel level sensor.
Lines are ran down the driver side of the car and comes up and around the booster. The regulator mounts to the booster.
*DOES NOT INCLUDE THE FEUL RAILS*
$1,500.00 PLUS SHIPPING
pump
18671 - Eliminator Corvette Stealth Kit
Fits 2003 1/2 and later Corvettes (Late C5 and C6)
• Supports up to 1900 HP – naturally aspirated
• Supports up to 1400 HP – forced air induction
• ORB-08 outlet port
• ORB-06 return port
• Incorporates factory jet siphon system and sending unit
• Includes an integrated 100-Micron Stainless Steel pre-pump filter
• Utilizes the factory tank, o-ring, lock ring and mounting location
• Includes all necessary fittings and hardware to plumb the pump into your tank
Aeromotive 16306 - Aeromotive Billet Electric Fuel Pump Controllers
Aeromotive 13105 - Compact EFI Regulator
lines
-8 single feed to a Y block by the firewall to both ends of aftermarket rails.
-6 return to regulator to pump
all lines are PTFE Teflon hose so no fuel smell when you park your car in the garage and prolong life of the hose.
into on PTFE http://www.hotrod.com/techarticles/e...ce_fuel_hoses/
Comes with pump, lines, regulator, filter, check valve, fittings for aftermarket rails, and fuel pump controller
The pump replaces the stock unit, reuse your fuel level sensor.
Lines are ran down the driver side of the car and comes up and around the booster. The regulator mounts to the booster.
*DOES NOT INCLUDE THE FEUL RAILS*
$1,500.00 PLUS SHIPPING
Last edited by Proracing; 05-30-2013 at 07:32 PM.
#15
Pro
Thread Starter
Member Since: Dec 2010
Location: Davie Florida
Posts: 554
Likes: 0
Received 0 Likes
on
0 Posts
It is used, it was removed from my buddies car that he decided to turn his car in to an hpde car so he no lo get needed it. He is actually the mecanic at Horse Power Sales and before he removed it it was making about 800HP at the wheels with his setup. I bought it from him in the anticipation to put a supercharger on my car but I have since changed my mind only do to the cost. I will need to upgrade my auto transmission + the supercharger + wider rims and tires. I am already pushing 565HP to the ground on all motor and my tranny is starting to slip as it is, so the cost of putting a supercharger just went from about 8k to 16k for me. This is the only resson Ive decided to sell. Also it is a Horse Power Sales kit and it does come with the regulator and controller.