ok im lost - program spare key fob ?
Thread Starter
Instructor
Joined: Nov 2004
Posts: 213
Likes: 1
From: baton rouge la
ok im lost - program spare key fob ?
i bought a num 1 key fob on ebay with instructios,but they dont work,i have an 05 with push button ignition with a working number 2 ,,,please guide me ,,,thanks guys tony
Melting Slicks
Joined: Aug 2006
Posts: 2,167
Likes: 11
From: Powell TN
Cruise-In VIII Veteran
Method 1 - Key Fob Quick Learn
This procedure will add key fobs. Fobs will be numbered in sequence based on when they are programmed; if 2 fobs are currently programmed to the RCDLR, a fob programmed using this method will be numbered as Fob 3. This procedure requires that you have a known good key fob, a replacement key fob, and the vehicles mechanical key.
Important: This procedure is not available when the maximum number of fobs (4) have been programmed. If 4 key fobs are programmed to this RCDLR and this method is attempted, the driver information center (DIC) will display MAX FOBS LEARNED and the programming procedure will exit. Method 4 must be used in this instance.
1. The vehicle must be OFF.
2. Open the rear compartment.
3. Place a known key fob within the interior of the vehicle.
4. At the rear of the vehicle insert the vehicle key in the rear compartment lock cylinder located in the lower left and cycle the key 5 times within 5 seconds.
5. The DIC will display a message: READY FOR FOB X (X = fob 2, 3, or 4).
6. Place the replacement key fob in the glove box fob pocket with the buttons facing right.
7. A beep will occur and the DIC will display: READY FOR FOB X (X = fob 3 or 4) or MAX FOBS LEARNED.
8. If programming additional key fobs, repeat steps 5 and 6, or press the OFF/ACC portion of the ignition switch to exit programming mode.
9. Operate the active portion of each key fob to exit the programming and to verify correct system operation.
The number on the fob doesn't have anything to do with Driver Number. If you are wanting to change your fobs so that Fob 1 corresponds to Driver 1, I believe you will have to go to the dealer and hook it up to a Tech II.
Method 2 - Key Fob Slot Programming
This procedure will add or replace a key fob. Method 2 allows you to choose which location (slot) the unprogrammed fob will be learned to. If you are replacing a key fob, this method will erase the previously known key fob programmed to that particular slot. This procedure requires that you have a known good key fob, a replacement key fob, the vehicle mechanical key, and a scan tool.
Important: This procedure is not available when the maximum number of fobs (4) have been programmed. If 4 key fobs are programmed to this RCDLR and this method is attempted, the DIC will display MAX FOBS LEARNED and the programming procedure will exit. Method 4 must be used in this instance.
1. The vehicle must be OFF.
2. Open the rear compartment.
3. Place a known key fob within the interior of the vehicle.
4. At the rear of the vehicle insert the vehicle key in the rear compartment lock cylinder located in the lower left and cycle the key 5 times within 5 seconds.
5. Install a scan tool.
6. Use the scan tool, to access the following:
• Vehicle Control Systems
• Computer/Integrating Systems
• Module Replacement/Setup
• RCDLR
• Program Key Fobs
7. Select Fob X (X = 1, 2, 3, or 4) on the scan tool. This will be the slot you wish to program to.
8. Place the replacement key fob in the glove box pocket with the buttons facing right. A beep will occur indicating programming completion. The previously known fob is now erased.
9. If programming additional key fobs, repeat steps 4-8, or press the OFF/ACC portion of the ignition switch to exit programming.
10. Remove the scan tool.
11. Operate the active portion of each key fob to exit the programming and verify correct system operation.
This procedure will add key fobs. Fobs will be numbered in sequence based on when they are programmed; if 2 fobs are currently programmed to the RCDLR, a fob programmed using this method will be numbered as Fob 3. This procedure requires that you have a known good key fob, a replacement key fob, and the vehicles mechanical key.
Important: This procedure is not available when the maximum number of fobs (4) have been programmed. If 4 key fobs are programmed to this RCDLR and this method is attempted, the driver information center (DIC) will display MAX FOBS LEARNED and the programming procedure will exit. Method 4 must be used in this instance.
1. The vehicle must be OFF.
2. Open the rear compartment.
3. Place a known key fob within the interior of the vehicle.
4. At the rear of the vehicle insert the vehicle key in the rear compartment lock cylinder located in the lower left and cycle the key 5 times within 5 seconds.
5. The DIC will display a message: READY FOR FOB X (X = fob 2, 3, or 4).
6. Place the replacement key fob in the glove box fob pocket with the buttons facing right.
7. A beep will occur and the DIC will display: READY FOR FOB X (X = fob 3 or 4) or MAX FOBS LEARNED.
8. If programming additional key fobs, repeat steps 5 and 6, or press the OFF/ACC portion of the ignition switch to exit programming mode.
9. Operate the active portion of each key fob to exit the programming and to verify correct system operation.
The number on the fob doesn't have anything to do with Driver Number. If you are wanting to change your fobs so that Fob 1 corresponds to Driver 1, I believe you will have to go to the dealer and hook it up to a Tech II.
Method 2 - Key Fob Slot Programming
This procedure will add or replace a key fob. Method 2 allows you to choose which location (slot) the unprogrammed fob will be learned to. If you are replacing a key fob, this method will erase the previously known key fob programmed to that particular slot. This procedure requires that you have a known good key fob, a replacement key fob, the vehicle mechanical key, and a scan tool.
Important: This procedure is not available when the maximum number of fobs (4) have been programmed. If 4 key fobs are programmed to this RCDLR and this method is attempted, the DIC will display MAX FOBS LEARNED and the programming procedure will exit. Method 4 must be used in this instance.
1. The vehicle must be OFF.
2. Open the rear compartment.
3. Place a known key fob within the interior of the vehicle.
4. At the rear of the vehicle insert the vehicle key in the rear compartment lock cylinder located in the lower left and cycle the key 5 times within 5 seconds.
5. Install a scan tool.
6. Use the scan tool, to access the following:
• Vehicle Control Systems
• Computer/Integrating Systems
• Module Replacement/Setup
• RCDLR
• Program Key Fobs
7. Select Fob X (X = 1, 2, 3, or 4) on the scan tool. This will be the slot you wish to program to.
8. Place the replacement key fob in the glove box pocket with the buttons facing right. A beep will occur indicating programming completion. The previously known fob is now erased.
9. If programming additional key fobs, repeat steps 4-8, or press the OFF/ACC portion of the ignition switch to exit programming.
10. Remove the scan tool.
11. Operate the active portion of each key fob to exit the programming and verify correct system operation.
Last edited by 'VETTE PHASE; Jul 9, 2008 at 11:54 PM.
Team Owner
Joined: May 2004
Posts: 82,175
Likes: 1,319
From: McKinney TX
St. Jude Donor '21-'22-'23-'24
The fob that you have that is not yet programmed for your car can only be programmed as a #1 fob or a #2 fob by using method 2 in the post above by 2000C-5. YOU MUST PROGRAM BOTH FOBS, even the one the car already recognizes, when you use that procedure.
If you screw it up, it's possible you could wind up with no fobs that will start your car and your car would have to be flat-bedded to the dealer to fix it.
If you screw it up, it's possible you could wind up with no fobs that will start your car and your car would have to be flat-bedded to the dealer to fix it.
Instructor
Joined: Nov 2007
Posts: 123
Likes: 0
From: Los Angeles California
Method 1 - Key Fob Quick Learn
This procedure will add key fobs. Fobs will be numbered in sequence based on when they are programmed; if 2 fobs are currently programmed to the RCDLR, a fob programmed using this method will be numbered as Fob 3. This procedure requires that you have a known good key fob, a replacement key fob, and the vehicles mechanical key.
Important: This procedure is not available when the maximum number of fobs (4) have been programmed. If 4 key fobs are programmed to this RCDLR and this method is attempted, the driver information center (DIC) will display MAX FOBS LEARNED and the programming procedure will exit. Method 4 must be used in this instance.
1. The vehicle must be OFF.
2. Open the rear compartment.
3. Place a known key fob within the interior of the vehicle.
4. At the rear of the vehicle insert the vehicle key in the rear compartment lock cylinder located in the lower left and cycle the key 5 times within 5 seconds.
5. The DIC will display a message: READY FOR FOB X (X = fob 2, 3, or 4).
6. Place the replacement key fob in the glove box fob pocket with the buttons facing right.
7. A beep will occur and the DIC will display: READY FOR FOB X (X = fob 3 or 4) or MAX FOBS LEARNED.
8. If programming additional key fobs, repeat steps 5 and 6, or press the OFF/ACC portion of the ignition switch to exit programming mode.
9. Operate the active portion of each key fob to exit the programming and to verify correct system operation.
The number on the fob doesn't have anything to do with Driver Number. If you are wanting to change your fobs so that Fob 1 corresponds to Driver 1, I believe you will have to go to the dealer and hook it up to a Tech II.
Method 2 - Key Fob Slot Programming
This procedure will add or replace a key fob. Method 2 allows you to choose which location (slot) the unprogrammed fob will be learned to. If you are replacing a key fob, this method will erase the previously known key fob programmed to that particular slot. This procedure requires that you have a known good key fob, a replacement key fob, the vehicle mechanical key, and a scan tool.
Important: This procedure is not available when the maximum number of fobs (4) have been programmed. If 4 key fobs are programmed to this RCDLR and this method is attempted, the DIC will display MAX FOBS LEARNED and the programming procedure will exit. Method 4 must be used in this instance.
1. The vehicle must be OFF.
2. Open the rear compartment.
3. Place a known key fob within the interior of the vehicle.
4. At the rear of the vehicle insert the vehicle key in the rear compartment lock cylinder located in the lower left and cycle the key 5 times within 5 seconds.
5. Install a scan tool.
6. Use the scan tool, to access the following:
• Vehicle Control Systems
• Computer/Integrating Systems
• Module Replacement/Setup
• RCDLR
• Program Key Fobs
7. Select Fob X (X = 1, 2, 3, or 4) on the scan tool. This will be the slot you wish to program to.
8. Place the replacement key fob in the glove box pocket with the buttons facing right. A beep will occur indicating programming completion. The previously known fob is now erased.
9. If programming additional key fobs, repeat steps 4-8, or press the OFF/ACC portion of the ignition switch to exit programming.
10. Remove the scan tool.
11. Operate the active portion of each key fob to exit the programming and verify correct system operation.
This procedure will add key fobs. Fobs will be numbered in sequence based on when they are programmed; if 2 fobs are currently programmed to the RCDLR, a fob programmed using this method will be numbered as Fob 3. This procedure requires that you have a known good key fob, a replacement key fob, and the vehicles mechanical key.
Important: This procedure is not available when the maximum number of fobs (4) have been programmed. If 4 key fobs are programmed to this RCDLR and this method is attempted, the driver information center (DIC) will display MAX FOBS LEARNED and the programming procedure will exit. Method 4 must be used in this instance.
1. The vehicle must be OFF.
2. Open the rear compartment.
3. Place a known key fob within the interior of the vehicle.
4. At the rear of the vehicle insert the vehicle key in the rear compartment lock cylinder located in the lower left and cycle the key 5 times within 5 seconds.
5. The DIC will display a message: READY FOR FOB X (X = fob 2, 3, or 4).
6. Place the replacement key fob in the glove box fob pocket with the buttons facing right.
7. A beep will occur and the DIC will display: READY FOR FOB X (X = fob 3 or 4) or MAX FOBS LEARNED.
8. If programming additional key fobs, repeat steps 5 and 6, or press the OFF/ACC portion of the ignition switch to exit programming mode.
9. Operate the active portion of each key fob to exit the programming and to verify correct system operation.
The number on the fob doesn't have anything to do with Driver Number. If you are wanting to change your fobs so that Fob 1 corresponds to Driver 1, I believe you will have to go to the dealer and hook it up to a Tech II.
Method 2 - Key Fob Slot Programming
This procedure will add or replace a key fob. Method 2 allows you to choose which location (slot) the unprogrammed fob will be learned to. If you are replacing a key fob, this method will erase the previously known key fob programmed to that particular slot. This procedure requires that you have a known good key fob, a replacement key fob, the vehicle mechanical key, and a scan tool.
Important: This procedure is not available when the maximum number of fobs (4) have been programmed. If 4 key fobs are programmed to this RCDLR and this method is attempted, the DIC will display MAX FOBS LEARNED and the programming procedure will exit. Method 4 must be used in this instance.
1. The vehicle must be OFF.
2. Open the rear compartment.
3. Place a known key fob within the interior of the vehicle.
4. At the rear of the vehicle insert the vehicle key in the rear compartment lock cylinder located in the lower left and cycle the key 5 times within 5 seconds.
5. Install a scan tool.
6. Use the scan tool, to access the following:
• Vehicle Control Systems
• Computer/Integrating Systems
• Module Replacement/Setup
• RCDLR
• Program Key Fobs
7. Select Fob X (X = 1, 2, 3, or 4) on the scan tool. This will be the slot you wish to program to.
8. Place the replacement key fob in the glove box pocket with the buttons facing right. A beep will occur indicating programming completion. The previously known fob is now erased.
9. If programming additional key fobs, repeat steps 4-8, or press the OFF/ACC portion of the ignition switch to exit programming.
10. Remove the scan tool.
11. Operate the active portion of each key fob to exit the programming and verify correct system operation.
let me tell you guys something, I went to a Chevrolet Dealer with my 08' C6, to get 2 new keys and keyfobs.
I went to the parts department and ordered 2 key fobs and keys, when they came in, I went to pick them up, and made a appointment with the service department.
The next day, I went to the service department at 8 O'Clock. The service technician told me that I couldn't use the new 08 FOBs, and needed to use the old FOBs. I was surprised... So I exchanged one of the 08 ones for a older version, but kept one of the new 08's because I had a hunch it could work..
So I had to come in again at 11:00, because they had to order the FOBs. Then after a hour and a half of waiting, at 12:30, the service tech told me that. "their programmer was malfunctioning, it says its okay, but then it doesn't work", and told me to, "maybe call us tomorrow and see if its working, or you could try another chevrolet dealer'.
So I went home, having wasted a lot of time.
Then I went on Corvette forum and found your post, followed it. and programed both my new keyfobs. the 08' version and the old version... all by myself.
It's pretty ridiculous that the service department of a Chevrolet dealer can't do what I just did by just following some very very useful instructions..
Melting Slicks
Joined: Aug 2006
Posts: 2,167
Likes: 11
From: Powell TN
Cruise-In VIII Veteran
Actually, if you wanted to start from scratch, you can. It works the same way as Method 1 above, except that it takes 30 minutes before it will start the programming. The DIC will countdown the 30 minutes for you and say "Ready for Fob 1". I guess the 30 minutes is so that someone can't jump in your car and program a fob real quick to steal your car.
Racer
Joined: Oct 2008
Posts: 457
Likes: 0
From: W. Columbia SC
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
Top 10 Most Expensive Corvettes Ever Sold on Bring A Trailer
Brett Foote
10 Things Every Corvette Owner Needs (2026 Edition)
Michael S. Palmer
8 Most "Only Corvette Owners Understand" Quirks and Problems
Pouria Savadkouei
10 Reasons the C6 Z06 is Still A Performance Benchmark After 20 Years
Joe Kucinski
How Much Horsepower Every Corvette Engine "LOST" in 1972
Joe Kucinski
Top 10 DOs and DON'Ts for Protecting Your Convertible Top!
Michael S. Palmer
Top 10 Most Explosive Corvettes Ever Made: Power-to-Weight Ratio Ranked!
Joe Kucinski
150 hp to 1,250 hp: Every Corvette Generation Compared by the Specs That Matter
Joe Kucinski
8 Coolest Corvette Pace Cars (and Replicas) of All Time
Verdad Gallardo
Le Mans Master
Joined: Aug 2000
Posts: 6,486
Likes: 1,659
From: Las Vegas NV
For C6's that won't go into "fob learn mode", try this... 
http://forums.corvetteforum.com/1570351932-post19.html
Cheers,
Kent
http://forums.corvetteforum.com/1570351932-post19.html
Cheers,
Kent
Team Owner
Joined: May 2004
Posts: 82,175
Likes: 1,319
From: McKinney TX
St. Jude Donor '21-'22-'23-'24
