Looks good to me.
All done
Drifting
Joined: Sep 2011
Posts: 1,423
Likes: 231
From: Licking MO
Thanks...BUT....what doesn't show up in the pictures is the RED stitching in the wheel and anything else would be to much for that area. Nothing much else you can to to the wheel. My thoughts were to remove all the brushed aluminum from the interior and add the Hyrocarbon in places where you would not nomally see color....like the seat sides, HUD display facia and the AC vent trim.
Team Owner
Joined: Feb 2006
Posts: 61,129
Likes: 1,361
From: North Carolina
As the Captain said...he was like a little kid in the back seat but I loved every minute of it! This came out very nice and the Captain even helped a little.....
The only hard part was getting to all the screws and clips to get the passenger dash pad off to install the AC vent trim rings.
Now on to the engine bay.
The only hard part was getting to all the screws and clips to get the passenger dash pad off to install the AC vent trim rings.
Now on to the engine bay.
Last edited by American Hydrocarbon; Dec 14, 2015 at 03:55 PM.
Melting Slicks
Joined: Dec 2014
Posts: 2,778
Likes: 2,306
From: Central UT
Meant to comment on this when I saw it before - what a unique combination! I'll bet it looks even better in person. And always remember, modding a car you really like is similar to Lay's chips during a good football game - - - you just can't stop! Nicely done. 
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
How Much Horsepower Every Corvette Engine "LOST" in 1972
Joe Kucinski
Top 10 DOs and DON'Ts for Protecting Your Convertible Top!
Michael S. Palmer
Top 10 Most Explosive Corvettes Ever Made: Power-to-Weight Ratio Ranked!
Joe Kucinski
150 hp to 1,250 hp: Every Corvette Generation Compared by the Specs That Matter
Joe Kucinski
8 Coolest Corvette Pace Cars (and Replicas) of All Time
Verdad Gallardo
Top 10 Corvette Engines RANKED by Peak Torque (70+ Years of Muscle!)
Joe Kucinski
Corvette ZR1X Will Be Pacing the Indy 500, And Could Probably Race, Too!
Verdad Gallardo
Top 10 Corvettes Coming to Mecum Indy 2026!
Brett Foote
Top 10 C9 Corvette MUST-HAVES to Fix These C8 Generation Flaws!
Michael S. Palmer
Thread Starter
Safety Car
Joined: Nov 2007
Posts: 4,446
Likes: 313
From: Tarpon Springs FL
FL Events Coordinator
I thought about doing just that as I have a Black Carbon Flash holder....But when you see it in person...it really goes well with the rest of the car.....Remember the front splitter and side rails...nothing on the back EXCEPT the plate holder....
SUPPORT AUTISM
Joined: Sep 2009
Posts: 1,954
Likes: 48
From: Suffolk County New York
St. Jude Donor '10, '14
That looks very sharp. At first I thought it was too much red, but I corrected myself. Nice job by the installer also. Be careful not to over do it. Looks great now as it is.
Thread Starter
Safety Car
Joined: Nov 2007
Posts: 4,446
Likes: 313
From: Tarpon Springs FL
FL Events Coordinator
Like the HEADING said ALL DONE. The only thing I didn't install are the splash guards....they did the WHOLE guard instead of just the edge. Since they are a snap to install...when I do a show I will just pop them on and then take em off for the ride home. They really finish the exterior off and make the wheel wells SPARKLE.