FS: Vette Lights: Oracle SMD Concept Side Markers
#222
Drifting
For you guys who have installed these on a Z06, what's the secret to accessing the front lights? The backs were easy, done in 15 minutes, but after removing the 3 bolts that go through the spats I don't see any way to pull the fender liner apart to expose the markers like on the back. How did you do it?
Thanks.
Thanks.
#224
Supporting Vendor
Thread Starter
Originally Posted by C5LOU
Got them done this morning, they look great!
Glad they arrived safe and sound! Would you happen to have any pics of them?
__________________
Cole Manzelli
Cole@Vette-Lights.com
(405) 209-5328
Vette-Lights.com
"FORUM10" - 10% Off Almost All Upgrades
___________
C5 Collection
C6 Collection
C7 Collection
Cole Manzelli
Cole@Vette-Lights.com
(405) 209-5328
Vette-Lights.com
"FORUM10" - 10% Off Almost All Upgrades
___________
C5 Collection
C6 Collection
C7 Collection
#225
Drifting
#226
Advanced
#227
Drifting
It's more difficult with the fender spats on the Z06. I just had to be more persistent! I used a couple plastic pry bars to get more room for my big hands, of course gently to avoid any scratches to the bodywork. Once I had room (although not much room) the challenge was to get the last clip on the lights out of the slots they clip into. It was much more difficult than the rears for me, but patience and persistence paid off, and that's about the only tip I can give you! Without spats I'm sure the fronts are probably as easy as the rears.
#228
Advanced
It's more difficult with the fender spats on the Z06. I just had to be more persistent! I used a couple plastic pry bars to get more room for my big hands, of course gently to avoid any scratches to the bodywork. Once I had room (although not much room) the challenge was to get the last clip on the lights out of the slots they clip into. It was much more difficult than the rears for me, but patience and persistence paid off, and that's about the only tip I can give you! Without spats I'm sure the fronts are probably as easy as the rears.
Last edited by BCSoCal; 05-17-2018 at 01:13 PM.
#229
Supporting Vendor
Thread Starter
#230
Melting Slicks
The spats make the front a PITA. I removed my front markers from the outside of the car, rather than gaining access to the rear of the marker and releasing the clips. VERY gentle with a plastic pry tool, then slid a credit card behind the light and the bumper cover to release the clip. Came right out (After spending 30+ minutes taking off panels, spats, wheel, wheel liner etc etc on the first side)
Last edited by atljar; 05-26-2018 at 09:42 PM.
#231
Supporting Vendor
Thread Starter
The spats make the front a PITA. I removed my front markers front the outside of the car, rather than gaining access to the rears and releasing the slips. VERY gentle with a plastic pry tool, then slid a credit card behind the light and the bumper cover to release the clip. Came right out (After spending 30+ minutes taking off panels, spats, wheel, wheel liner etc etc on the first side)
#232
Supporting Vendor
Thread Starter
Unpainted units are ready to rock & roll!
Painted units are painted to order so typically experience a 3-5 week delay
Painted units are painted to order so typically experience a 3-5 week delay
#233
Le Mans Master
Dumb question I know.
But the side markers don't come on until the headlights come on (at night).
Has anyone figured out a way for them to come on automatically during the day?
Yes, I know you can manually turn them on.
Thanks.
But the side markers don't come on until the headlights come on (at night).
Has anyone figured out a way for them to come on automatically during the day?
Yes, I know you can manually turn them on.
Thanks.
#234
Supporting Vendor
Thread Starter
There's likely a much easier way to do it but the first method that comes to mind would be to run a jumper wire from the DRL's to the side markers with a one-way diode inline.
#236
Supporting Vendor
Thread Starter
Thursdays are the best days to place orders for painted sets to experience a minimum down time!
#237
I need a set Blacked out just like those. Shoot me the price etc.
Thanks
Thanks
#238
Supporting Vendor
Thread Starter