C7 Tech/Performance Corvette Technical Info, Internal Engine, External Engine, Tech Topics, Basic Tech, Maintenance, How to Remove & Replace
Sponsored by:
Sponsored by:

Wiring harness routing.

Thread Tools
 
Search this Thread
 
Old 02-10-2018, 11:37 AM
  #1  
Ghostnotes
Racer
Thread Starter
 
Ghostnotes's Avatar
 
Member Since: May 2017
Location: Pasadena Texas
Posts: 455
Received 33 Likes on 30 Posts
Default Wiring harness routing.

Its been almost 2 months since i pulled the engine and can not remember which way this wiring harness goes. Not sure if it goes to the left of the motor mount(Red arrow), running along the oil pan or to the right/outside of the mount. There are 2 push mounts. One circled in red is obvoulsy mounted in the correct position. I can't find where to land the one circled in yellow, unless it goes on the other side of the mount mounting with the oil pan further down.

I had taken pics but i destroyed my phone recently and this is the only thing holding me up.
If by any chance somebady has their car up in the air, can you take a look. This is the passenger side.

​​​​​​​Thanks.
Attached Images  
Old 02-10-2018, 09:46 PM
  #2  
lakemg
Melting Slicks
 
lakemg's Avatar
 
Member Since: Aug 2014
Posts: 2,746
Received 909 Likes on 606 Posts
Default

Mine's a pain in the *** to get to at the moment since I have it bundled up in storage, but here's a bump for you...
Old 02-10-2018, 10:12 PM
  #3  
Ghostnotes
Racer
Thread Starter
 
Ghostnotes's Avatar
 
Member Since: May 2017
Location: Pasadena Texas
Posts: 455
Received 33 Likes on 30 Posts
Default

Thanks.
Old 02-14-2018, 03:03 AM
  #4  
Ghostnotes
Racer
Thread Starter
 
Ghostnotes's Avatar
 
Member Since: May 2017
Location: Pasadena Texas
Posts: 455
Received 33 Likes on 30 Posts
Default

Bump
Old 02-14-2018, 08:15 AM
  #5  
Dale002
Melting Slicks
 
Dale002's Avatar
 
Member Since: Jul 2010
Location: Between Tally and Gatorville ,Florida
Posts: 3,454
Received 83 Likes on 69 Posts

Default

The hardness runs between the engine block and the pass mount. ( Yellow area )
Old 02-14-2018, 08:25 AM
  #6  
Ghostnotes
Racer
Thread Starter
 
Ghostnotes's Avatar
 
Member Since: May 2017
Location: Pasadena Texas
Posts: 455
Received 33 Likes on 30 Posts
Default

Originally Posted by Dale002
The hardness runs between the engine block and the pass mount. ( Yellow area )
That is what i figured. It looked like another place to mount the yellow on the pan/block.
Thanks
Old 02-14-2018, 08:27 AM
  #7  
Dale002
Melting Slicks
 
Dale002's Avatar
 
Member Since: Jul 2010
Location: Between Tally and Gatorville ,Florida
Posts: 3,454
Received 83 Likes on 69 Posts

Default

Originally Posted by Ghostnotes
That is what i figured. It looked like another place to mount the yellow on the pan/block.
Thanks
Sorry, Not Through the Yellow area, where you have it highlighted in Red.
goes to the left of the motor mount(Red arrow), running along the oil pan

Last edited by Dale002; 02-14-2018 at 08:29 AM.

Get notified of new replies

To Wiring harness routing.




Quick Reply: Wiring harness routing.



All times are GMT -4. The time now is 01:03 PM.