Go Back  CorvetteForum - Chevrolet Corvette Forum Discussion > C7 Corvette > C7 Vendor for Sale
Reload this Page >

C7 Corvette Stingray A&A Supercharger Kit LT1 V3 Si-trim 4.0" @ PFYC-PartsForYourCar

Notices
C7 Vendor for Sale Exclusive forum for vendors to list C7 products, services and promotions.
Sponsored by:
Sponsored by:

C7 Corvette Stingray A&A Supercharger Kit LT1 V3 Si-trim 4.0" @ PFYC-PartsForYourCar

 
Old 12-30-2015, 05:30 PM
  #1  
PFYC
Platinum Supporting Vendor
Thread Starter
 
PFYC's Avatar
 
Member Since: Nov 2004
Location: Ohio
Posts: 1,718
Received 29 Likes on 28 Posts
Default C7 Corvette Stingray A&A Supercharger Kit LT1 V3 Si-trim 4.0" @ PFYC-PartsForYourCar

2014 2015 2016 2016 C7 Corvette Stingray SC Kit LT1 V3 Si-trim 4.0"

A&A Corvette produced the first C7 Corvette supercharger system in October of 2013. After much testing and a few “tweaks” here and there, production systems became available in January of 2014. Aesthetically as well as mechanically, we believe this to be the finest system available for the new C7 Stingray.

Take a close look and we’re sure you’ll agree!

Advantages of the A&A Supercharger system:

Proprietary supercharger units built specifically for A&A Corvette by Vortech Engineering are used exclusively. We have found Vortech to build the most efficient units available and to also offer us the best available customer service and support. Self- contained V3 Si head units are standard. The Si units are the most efficient model available in the 500 to 700 horsepower range. All our units are available in a highly polished or satin black finish.

We have larger units available, capable of well over 1000 horsepower for properly built engines.







A&A is the only manufacturer to include a fully machined SFI approved balancer with interchangeable lower pulleys as standard equipment. Others just use a simple pulley that bolts to the stock cast iron balancer. Which would you trust?

This balancer design allows us to use a dedicated 8 rib belt that does not interfere with the water pump or alternator belt.

A&A continues as the leader in intercooler design with our new C7 Ram Air Intercooler. GM did a great job sealing in the radiator cavity from the grill opening to the radiator. This whole cavity is a high pressure area when the vehicle is at speed. After carefully looking at all placement and airflow direction options, we came up with our present design. The intercooler lays flat and is hidden behind the bumper cover. We weld an aluminum scoop to the intercooler which protrudes into the incoming air stream and directs it through the intercooler and out the bottom. Any air that is grabbed by the scoop is literally rammed through the intercooler core. Simple physics won’t allow it to go anywhere else. Hence the name “Ram Air Intercooler”.

Others went with the flat placement but forgot all about directing airflow through the cooler. Laying the intercooler flat and putting a plastic air dam behind it just isn’t going to work efficiently. Not only are they asking the air to abruptly make a right angle turn, they’re also trying to get the air to flow from a low pressure area (under the car) into a high pressure area (inside the radiator cavity.) A&A wins this one hands down.

Our bracket design once again stands out from the crowd. Amazingly stiff while remaining simple, it really is a work of art. We have solid billet mounts that attach the main bracket to the block and the cylinder head. Our cylinder head mount has FOUR mounting points. Others use a simple spacer with one long bolt going through the middle. This can rotate under extreme forces. Ours simply cannot move in any direction.

Our bracket uses steel idler and tensioner pulleys with dual bearings and the proper stanchions to support the bearings.

Even better for the consumer is that our entire bracket, pulley and supercharger assembly comes completely preassembled for you. Take it out of the box and bolt it onto the block and cylinder head without having to assemble a thing. Even the mounting bolts are “zip-tied” in the proper holes. It really is a 5 minute proposition to bolt the entire supercharger and bracket assembly on the engine.









Great Power For the $$$$$$$

2014 2015 2016 2016 C7 Corvette Stingray SC Kit LT1 V3 Si-trim 4.0"
__________________


PFYC.COM - Proudly Serving You For Over 20 Years! Call Us Toll Free: 866.695.PFYC (7392)
www.pfyc.com [email protected] .."we're here to help"
Use Code SAVESIX At Checkout And Save!
PFYC is offline  
Old 10-06-2016, 06:48 PM
  #2  
PFYC
Platinum Supporting Vendor
Thread Starter
 
PFYC's Avatar
 
Member Since: Nov 2004
Location: Ohio
Posts: 1,718
Received 29 Likes on 28 Posts
Default

Pfyc Would like to thank you for alll your support over the years

Pfyc is here for all your C7 needs

Please visit www.pfyc.com
__________________


PFYC.COM - Proudly Serving You For Over 20 Years! Call Us Toll Free: 866.695.PFYC (7392)
www.pfyc.com [email protected] .."we're here to help"
Use Code SAVESIX At Checkout And Save!
PFYC is offline  
Old 10-06-2016, 07:15 PM
  #3  
S'vette
CF Senior Member
 
S'vette's Avatar
 
Member Since: Aug 2010
Location: El Paso TX
Posts: 2,945
Received 15 Likes on 12 Posts
Default

What is the average install time for this kit if being done at a shop that does this kind of work? Is there any physical mods to the engine bay or parts?

Last edited by S'vette; 10-06-2016 at 07:16 PM.
S'vette is offline  
Old 10-06-2016, 07:35 PM
  #4  
PFYC
Platinum Supporting Vendor
Thread Starter
 
PFYC's Avatar
 
Member Since: Nov 2004
Location: Ohio
Posts: 1,718
Received 29 Likes on 28 Posts
Default

Originally Posted by S'vette View Post
What is the average install time for this kit if being done at a shop that does this kind of work? Is there any physical mods to the engine bay or parts?

When i worked for a shop that did installs it was about 12-16 hours total with tune
PFYC is offline  
Old 10-24-2016, 06:36 PM
  #5  
PFYC
Platinum Supporting Vendor
Thread Starter
 
PFYC's Avatar
 
Member Since: Nov 2004
Location: Ohio
Posts: 1,718
Received 29 Likes on 28 Posts
Default

Pfyc Would like to thank you for alll your support over the years

Pfyc is here for all your C7 needs

Please visit www.pfyc.com
__________________


PFYC.COM - Proudly Serving You For Over 20 Years! Call Us Toll Free: 866.695.PFYC (7392)
www.pfyc.com [email protected] .."we're here to help"
Use Code SAVESIX At Checkout And Save!
PFYC is offline  
Old 06-10-2019, 12:38 PM
  #6  
PFYC
Platinum Supporting Vendor
Thread Starter
 
PFYC's Avatar
 
Member Since: Nov 2004
Location: Ohio
Posts: 1,718
Received 29 Likes on 28 Posts
Default

Save 6% off your order!! Use promo code: SAVESIX
PFYC is offline  

Thread Tools
Search this Thread
Quick Reply: C7 Corvette Stingray A&A Supercharger Kit LT1 V3 Si-trim 4.0" @ PFYC-PartsForYourCar


Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
 
  • Ask a Question
    Get answers from community experts
Question Title:
Description:
Your question will be posted in: