E.C.P

High all just finished a deal on some fresh low mileage 03 Z06 heads
(243 castings)
These are fresh take offs from 03 Z06's done at Lg Motorsports .
They are the ones with the light weight sodium filled valves.
A great performance addition to the LS6 intake and headers.
They are complete minus valve covers and coil brackets.
LS1's are perimeter bolt pattern and LS6's are center bolt .I will see what I can do on a price for these two items as well as gaskets. Your choice of the factory or cometic gaskets.
You will need to transfer your LS1 rockers and supports onto the LS6 heads as well . Or up-grade to the Yella terra or Harlan sharp ,again I will get pricing if needed on the those rockers

ONLY 3 SET'S AVAILABLE
Price is :
Heads only $750.00 + taxes
Heads & installation $1850.00 +taxes --aprox install time 12 hours

PM,email (nastyvette@sympatico.ca) or call (519-622-9389)

terry621

Hey Manny

are you trying to put us all in the poor house or the clinic for CSM
(can't stop modding)

we'll talk

E.C.P

Terry you've got it all wrong.
It's all about keeping up to Mo & Steve

E.C.P

This is a great deal if you are looking to get into the a set of heads with out breaking the bank. This set-up with a cam, cold air intake/LS6 intake /P&P TB & headers on an LS1 with a good tune, should put you near the 375RWHP mark.

Thx
Manny

eb02z06

You'll need a 02-04 LS6 cam to acheive those numbers, heads only are worth about 10-15 over 241 castings-again it all depends how much your pistons sit out of the hole.

MYRagtop

I don't think that putting LS6 heads on will get you 375 RWH and if that is your goal then just getting a good cam should get you there..... and for quite a bit less too.

JPEAK

You're right, but why would you spend that money on used LS6 heads and all that labour, why not spend a little more for Patriots, Darts or for the mother load AFR and get the most out of the heads. Seems a waist of labour $$ to only go half way.

E.C.P

Some like the 243 casting choice as it is much less than the $1300 -$2500 plus for the Patroit to AFR heads . Everyones budget is different.
There are many on this forum that have gone this route with excellent results. Not everyone is after much more than 435-450 RWHP.

E.C.P

I did add to the post where I missed writing in the cam. My mistake,but I have since fixed it.

JPEAK

No you're charging $775 for used heads where new CNC stage 1 243heads are only in the $1200 range, so there is only a $500 difference for much more performance.

E.C.P

$500 for some maybe more they are willing pay. The extra $500 would almost pay for the install.
That's why we have choices and selection .
So that all have buy at their comfort level .

JPEAK

Not quite, your install is nearly $1200.

E.C.P

Why yes it is. So now your up to almost 4g's. Like I said its a choice. I already know your's on anything and everything

JPEAK

No you're up to nearly 2G's for 10 to 15 hp.

GettReal

in all fairness to this response... 100.00 per 1 rwhp is typical.

E.C.P

Ok Walter you win.
I guess the $1300+ we spend for 15-20 hp on headers and the $300-$400 on cold air intakes for 5-10hp and the $500-$1000 on intakes for 5-15hp ect,ect.ect is just not worth it .So I guess we should all just stop wasting our money on mods

If your motive was not so personal,I might actually be bothered

JPEAK

LOL

Highway Hawk

You guys need a timeout! Look, anyone is free to try and sell stuff and ask whatever they want. Everyone else is free to decide for themselves whether they want to pay what is being asked. If you don't like the price move on to the next forum topic, don't berate the person doing the selling and don't argue about what the price should be.

It's not in keeping with the spirit of the forum and it's counter-productive to the community we've built here.

BBaysdon

Is that $750.00 shipped.

E.C.P

I can do that