[Z06] Best ported heads for power
#1
Drifting
Thread Starter
Member Since: Dec 2015
Location: Wes is gay :) California
Posts: 1,776
Received 59 Likes
on
56 Posts
Best ported heads for power
Looking for cost to HP in this case with ported ls7 heads AHP can port heads for 800$ only one I know of as right now. Is there any other company that has better heads for around the same price? And what do I expect ported heads? I have a btr4 cam and getting a ported msd
#2
You will get every answer in here with a question like that.
For ported stock LS7 castings I have seen best power with either WCCH or AI.
Best power period without budget Mamo 265s or Mast
For ported stock LS7 castings I have seen best power with either WCCH or AI.
Best power period without budget Mamo 265s or Mast
The following 2 users liked this post by lt1z:
CammedC6520 (08-31-2017),
FSTFRC (09-09-2017)
#4
Looking for cost to HP in this case with ported ls7 heads AHP can port heads for 800$ only one I know of as right now. Is there any other company that has better heads for around the same price? And what do I expect ported heads? I have a btr4 cam and getting a ported msd
CammedC6520,
Our heads cam intake LS7 cars are throwing down over 600+ horse and 550+ torque to the tire on 93. If you're looking for a package deal or need your heads ported/fixed, give me a shout! Good luck on your build!
-Russ
The following 3 users liked this post by FrankensteinE.D.:
#5
Drifting
Thread Starter
Member Since: Dec 2015
Location: Wes is gay :) California
Posts: 1,776
Received 59 Likes
on
56 Posts
Attachment 48201885
CammedC6520,
Our heads cam intake LS7 cars are throwing down over 600+ horse and 550+ torque to the tire on 93. If you're looking for a package deal or need your heads ported/fixed, give me a shout! Good luck on your build!
-Russ
CammedC6520,
Our heads cam intake LS7 cars are throwing down over 600+ horse and 550+ torque to the tire on 93. If you're looking for a package deal or need your heads ported/fixed, give me a shout! Good luck on your build!
-Russ
My heads are AHP milled and fixed I just need porting how much do you charge for porting only?
The following users liked this post:
Kris_wh5 (06-15-2021)
#6
The following users liked this post:
CammedC6520 (08-31-2017)
#8
Melting Slicks
..my buddy picked up I believe if I remember from a few months ago. 46 rwhp and 44 rwtq from his 280 AIs milled .020 IIRC. (has Torquer 110). 98 octane mix. Full Exhaust port picks up big flow with 1 7/8" LT's. Mill is big power if you have the gas. Car is a total beast now.
#9
If your looking for the best Darin Morgan hands down he can make a go cart head do whatever you want and flow very exceptionally, now you can get different heads out there and start from there.....you will get answers everywhere but unless your not concerned about money give Darin Morgan a call.....
Last edited by RamAir972003; 09-09-2017 at 02:06 AM.
The following users liked this post:
ElisTwoCents (04-20-2021)
#10
Safety Car
#11
Race Director
Member Since: Mar 2006
Location: Everywhere and Nowhere at all
Posts: 15,357
Received 1,679 Likes
on
1,135 Posts
The following users liked this post:
FSTFRC (09-09-2017)
#13
Melting Slicks
Being nice kid and not condescending, you can only reinvent the wheel so many times. To the other guy. Try getting Darin Morgan to port a set of LS7 heads. Or try to just get a hold of him period. Not gonna happen. He doesn't need that. What (companies/people) that have been mentioned here is the best of the best and what the fastest guys use 99% of the time.
Last edited by REDZED2; 09-09-2017 at 02:57 PM.
The following 2 users liked this post by REDZED2:
CammedC6520 (09-09-2017),
Millenium Z06 (09-09-2017)
#14
I'd go AI or Mamo, end of discussion.
That said, the OP has gone from H/C/I to a new motor to nitrous to a FI and now back to heads. Kinda like a dog chasing his tail...but the tail is smarter than the dog.
That said, the OP has gone from H/C/I to a new motor to nitrous to a FI and now back to heads. Kinda like a dog chasing his tail...but the tail is smarter than the dog.
Last edited by Millenium Z06; 09-09-2017 at 03:03 PM.
#15
Drifting
Thread Starter
Member Since: Dec 2015
Location: Wes is gay :) California
Posts: 1,776
Received 59 Likes
on
56 Posts
Being nice kid and not condescending, you can only reinvent the wheel so many times. To the other guy. Try getting Darin Morgan to port a set of LS7 heads. Or try to just get a hold of him period. Not gonna happen. He doesn't need that. What (companies/people) that have been mentioned here is the best of the best and what the fastest guys use 99% of the time.
I hate this iPhone with autocorrect
#17
Race Director
Member Since: Mar 2006
Location: Everywhere and Nowhere at all
Posts: 15,357
Received 1,679 Likes
on
1,135 Posts
#19
Whatever you decide to do I would definitely set your mind up on one thing with the motor.....and regardless who has more money than the other person you always listen and learn, others have been there done that in my case unfortunately I had to rebuild my motor.
If your heads are already done by AH Just send them there....
If your heads are already done by AH Just send them there....
Last edited by RamAir972003; 09-09-2017 at 04:32 PM.
The following users liked this post:
CammedC6520 (09-09-2017)
#20