GTG: Murphy, Plano, Wylie, Richardson, Garland, Sachse, and surrounding areas II
#941
Le Mans Master
This is just sick !
Love it !
I was wondering if this show was still on TV. The web site shows its on SUN TV, and MEN TV. What channels is that ? I'm guessing its only shown in Canada now (since its made there). That's a bummer...
http://www.dreamcargarage.com/dreamcargarage-home.php
Toque
Love it !
I was wondering if this show was still on TV. The web site shows its on SUN TV, and MEN TV. What channels is that ? I'm guessing its only shown in Canada now (since its made there). That's a bummer...
http://www.dreamcargarage.com/dreamcargarage-home.php
Toque
#942
Tech Contributor
Thread Starter
#943
Le Mans Master
#944
Le Mans Master
yup..
#947
Burning Brakes
Guys:
Just a heads up. Its a C5 and a C6 issue that I was able to fix on my car.
http://forums.corvetteforum.com/c5-g...the-other.html
Toque
Just a heads up. Its a C5 and a C6 issue that I was able to fix on my car.
http://forums.corvetteforum.com/c5-g...the-other.html
Toque
I checked mine last night after reading your post, guess what, its off by about 1/4".
I don't think it is enough to mess with right now but now I know it is off and it will bug me forever.
#948
Tech Contributor
Thread Starter
Sorry...
There are a lot of people finding out that they have the same issue.
I think I opened up a can of worms bringing up this issue.
These cars are not so "precision" built as some think.
There is some "slop" tolerance in various components for sure.
Mine is correct now though. Last night I drove it around the block, and my steering wheel is slightly turned to the right when driving straight, and my drivers side fender is 1/4" too high now. I can adjust the height easily enough. I was planning to get a full alignment anyway because I was still dialing in the coil overs. I should have everything dialed in soon, and once I get an alignment it should be prefect.
Toque
#949
Tech Contributor
Thread Starter
Video's from Car's coffee last weekend.
One hell of a cool spot to see WICKED car's.
Check out the Solstice at the end of the 2nd video....
One hell of a cool spot to see WICKED car's.
Check out the Solstice at the end of the 2nd video....
#950
Le Mans Master
LOL....
#953
Tech Contributor
Thread Starter
I noticed that last week...
I am going to have to start a new post soon.
I guess I'll call it :
GTG: Murphy, Plano, Wylie, Richardson, Garland, Sachse, and surrounding areas III
Unless anyone wants to change it...
Toque
I am going to have to start a new post soon.
I guess I'll call it :
GTG: Murphy, Plano, Wylie, Richardson, Garland, Sachse, and surrounding areas III
Unless anyone wants to change it...
Toque
#954
Safety Car
Sorry...
There are a lot of people finding out that they have the same issue.
I think I opened up a can of worms bringing up this issue.
These cars are not so "precision" built as some think.
There is some "slop" tolerance in various components for sure.
Mine is correct now though. Last night I drove it around the block, and my steering wheel is slightly turned to the right when driving straight, and my drivers side fender is 1/4" too high now. I can adjust the height easily enough. I was planning to get a full alignment anyway because I was still dialing in the coil overs. I should have everything dialed in soon, and once I get an alignment it should be prefect.
Toque
Last edited by David426; 04-11-2010 at 02:16 PM.
#955
Safety Car
Collin County Corvettes , Collin County Corvette Club, Collin County Corvette Clowns
#956
Tech Contributor
Thread Starter
Guys:
I can't make it tonight. Dr said I scratched my eye. I thought I just had dirt in it i could not get out. I am having a hard time keeping both eyes open cause of it... Drugs are helping a little...
I don't think driving would be a good idea...
See ya'll next week !
Toque
I can't make it tonight. Dr said I scratched my eye. I thought I just had dirt in it i could not get out. I am having a hard time keeping both eyes open cause of it... Drugs are helping a little...
I don't think driving would be a good idea...
See ya'll next week !
Toque
#958
Instructor
Member Since: Apr 2008
Location: Garland TX
Posts: 224
Likes: 0
Received 0 Likes
on
0 Posts
Rear Wheels Centered in Rear Quater panels ??????
I just had to check mine !!!!!!!!!!!!! within .050 fifty thousandths !!!!!!
Considering mfg tolerances in non precision fiberglass rear panels sheer luck !!!!!!!!!!!! Frankly I would not care if the offset was 3/4 inch if only the assy folks had torqued the rear axle nuts and pointed all 4 wheels in the same direction !!!!!!!!!!!!!!!!!!!!!! Toque if your wheels are not plumb vertically or the off set in both R&L rims equal you will be busy all spring chasing perfection. Maybe a wheel alignment would be a better starting point, Bob will assist you setting height where it needs to be.
Good Luck
Happy Cruising
Harry
Considering mfg tolerances in non precision fiberglass rear panels sheer luck !!!!!!!!!!!! Frankly I would not care if the offset was 3/4 inch if only the assy folks had torqued the rear axle nuts and pointed all 4 wheels in the same direction !!!!!!!!!!!!!!!!!!!!!! Toque if your wheels are not plumb vertically or the off set in both R&L rims equal you will be busy all spring chasing perfection. Maybe a wheel alignment would be a better starting point, Bob will assist you setting height where it needs to be.
Good Luck
Happy Cruising
Harry
#959
Burning Brakes
Glass Repair/Replace
I was wondering if any of you guys have a place that you would recommend for glass repairs? I am not sure if it can be repaired but I would like to have someone look at it. I think I might need them to come to my place to look at it before it grows.
#960
Le Mans Master
Rex's # is 972.670.0078
-Tim