Billet valve covers for the C6
Thread Starter
Former Vendor
Joined: Aug 2010
Posts: 1,013
Likes: 0
From: Oceanside ca.
Billet valve covers for the C6
Hello Corvetteforum members from Billet Customs Products!
I am Bruce and I wanted to introduce myself to this great forum. I am happy to announce I have designed and created a new product for the corvette enthusiast.
I am also happy to announce I will be at the Corvettes at Carlisle event in Carlisle, PA from August 27th to 29th, stop by and visit us to check out the new valve covers. Special pricing at the event.
Our Custom Billet Valve Covers are a complete bolt on upgrade
replacement for the stock GM valve covers. You will not need to relocate
your coil brackets or purchase any other custom part to complete the
installation. Everything you need is included. Your stock plug / coil wires
will not need to be replaced. Other than the GM gasket you will need to
purchase, no additional parts are required. The Billet Aluminum is
polished to a reflective finish. Our unique valve cover and coil bracket
system are made from 6061-T6 Aluminum Billet.
This “Patent Pending” product has been designed to upgrade & replace stock GM valve covers for C6 & Z06 Corvettes 2005-2010 specifically the LS2, LS3 and LS7 motors. Included is the new Stealth "Spider" coil bracket assembly. It is designed to be used together as a complete valve cover system. You will not find this valve cover system made by anyone else.
Our products are new & unique.
100% Billet Aluminum is machined to exact tolerances.
The Highest Quality Standards are used during manufacturing.
Built in the USA
Here’s a little about us:
As a lifelong Corvette lover, I enjoy a fast ride and clean head turning
engine compartment. You know, I want it to look like a real Corvette. After
looking for a valve cover product that would bring out the true Corvette
look, I found little that I liked. I was frustrated by the products that were on
the market. They all seem to have issues. I wanted to get rid of the ugly
plastic that seemed to be everywhere, and dump the stock covers along
with the massive coil brackets. But I did not want to relocate other
components because I knew it would end up costing me an arm and a
leg.
Most of the products I looked at were just plain ugly. You never really saw
much of the valve cover, mostly just the coils and the brackets.. The
covers that I liked were mostly cast aluminum, and required a coil
relocation, which meant more parts, and more money. Sometimes the
fuel lines needed to be replaced, or longer coil wires, or longer custom
electrical harnesses and so on. In frustration I created this product.
My system requires no additional parts other than a new stock GM
gasket. It is unique and has a look like no other. And it's solid aluminum
billet.
About Our Business
We are a new company that has spun off from a 30 year old
manufacturing business that has been successfully building products for
the military, medical and commercial industries. I have over 40 years
experience working in the manufacturing business.
All products that are manufactured have gone through several planned
in-process inspection procedures as well as a signed off Final
Inspection. All manufacturing is in compliance with the latest ISO Quality
standards.
The product you receive from us will have completed all inspection
requirements to insure that all critical dimensions have been maintained.
Quality will not be compromised
I am Bruce and I wanted to introduce myself to this great forum. I am happy to announce I have designed and created a new product for the corvette enthusiast.
I am also happy to announce I will be at the Corvettes at Carlisle event in Carlisle, PA from August 27th to 29th, stop by and visit us to check out the new valve covers. Special pricing at the event.
Our Custom Billet Valve Covers are a complete bolt on upgrade
replacement for the stock GM valve covers. You will not need to relocate
your coil brackets or purchase any other custom part to complete the
installation. Everything you need is included. Your stock plug / coil wires
will not need to be replaced. Other than the GM gasket you will need to
purchase, no additional parts are required. The Billet Aluminum is
polished to a reflective finish. Our unique valve cover and coil bracket
system are made from 6061-T6 Aluminum Billet.
This “Patent Pending” product has been designed to upgrade & replace stock GM valve covers for C6 & Z06 Corvettes 2005-2010 specifically the LS2, LS3 and LS7 motors. Included is the new Stealth "Spider" coil bracket assembly. It is designed to be used together as a complete valve cover system. You will not find this valve cover system made by anyone else.
Our products are new & unique.
100% Billet Aluminum is machined to exact tolerances.
The Highest Quality Standards are used during manufacturing.
Built in the USA
Here’s a little about us:
As a lifelong Corvette lover, I enjoy a fast ride and clean head turning
engine compartment. You know, I want it to look like a real Corvette. After
looking for a valve cover product that would bring out the true Corvette
look, I found little that I liked. I was frustrated by the products that were on
the market. They all seem to have issues. I wanted to get rid of the ugly
plastic that seemed to be everywhere, and dump the stock covers along
with the massive coil brackets. But I did not want to relocate other
components because I knew it would end up costing me an arm and a
leg.
Most of the products I looked at were just plain ugly. You never really saw
much of the valve cover, mostly just the coils and the brackets.. The
covers that I liked were mostly cast aluminum, and required a coil
relocation, which meant more parts, and more money. Sometimes the
fuel lines needed to be replaced, or longer coil wires, or longer custom
electrical harnesses and so on. In frustration I created this product.
My system requires no additional parts other than a new stock GM
gasket. It is unique and has a look like no other. And it's solid aluminum
billet.
About Our Business
We are a new company that has spun off from a 30 year old
manufacturing business that has been successfully building products for
the military, medical and commercial industries. I have over 40 years
experience working in the manufacturing business.
All products that are manufactured have gone through several planned
in-process inspection procedures as well as a signed off Final
Inspection. All manufacturing is in compliance with the latest ISO Quality
standards.
The product you receive from us will have completed all inspection
requirements to insure that all critical dimensions have been maintained.
Quality will not be compromised
