CorvetteForum - Chevrolet Corvette Forum Discussion
The painted metal collar that the steering wheel mounts to must be horizontal o the steering wheel spokes are level
The painted metal collar that the steering wheel mounts to must be horizontal o the steering wheel spokes are level
0 2020/02/26 06:09:06
Aluminum hub that painted collar mounts to
Aluminum hub that painted collar mounts to
0 2020/02/26 06:09:23
Correct position before installing horn button
Correct position before installing horn button
0 2020/02/26 06:09:39
PO had cut a large chunk of the carpet away, and it looked really bad. Pull new carpet over metal buckle and cut a slit for the buckle to come through, then put the carpet under the metal aluminum threshold
PO had cut a large chunk of the carpet away, and it looked really bad. Pull new carpet over metal buckle and cut a slit for the buckle to come through, then put the carpet under the metal aluminum threshold
0 2020/04/11 06:27:36
0 2020/04/11 06:27:47
Hope this helps
Hope this helps
0 2020/06/08 01:11:56
You can see that the rubber seal is gone from the edge of the flapper on mine.
You can see that the rubber seal is gone from the edge of the flapper on mine.
0 2020/07/03 08:41:42
The number below the rubber hoses
The number below the rubber hoses
0 2020/07/13 05:41:41
0 2020/07/13 05:41:50
0 2020/07/13 05:42:05
0 2020/07/13 05:42:15
Passenger side Low Beam bulb is on the left
Passenger side Low Beam bulb is on the left
0 2020/07/18 15:10:02
I hope this will help
I hope this will help
0 2020/08/08 08:10:15
The clear lens look too good for 47 years old
The clear lens look too good for 47 years old
0 2020/08/09 07:29:15
The catalog says 71 - 73
The catalog says 71 - 73
0 2020/08/09 07:29:25
I would like to know if the restoration lights have the Guide Numbers?
I would like to know if the restoration lights have the Guide Numbers?
0 2020/08/09 07:29:38
There ain’t a lot of meat around the hole placement, so be extra careful.
There ain’t a lot of meat around the hole placement, so be extra careful.
0 2020/08/11 09:15:38
If you look closely, this side started to brake off, I hit it with fiberglass resin, and then some paint
If you look closely, this side started to brake off, I hit it with fiberglass resin, and then some paint
0 2020/08/11 09:15:51
0 2020/08/11 09:16:01
Says this is a switch for 73_76.
Says this is a switch for 73_76.
0 2020/09/19 07:25:47
0 2020/09/24 11:19:23
0 2020/09/24 11:30:54
0 2020/10/08 00:51:09
Old oem
Old oem
0 2020/10/11 08:29:28
0 2020/10/11 08:29:35
0 2020/10/11 08:29:42
0 2020/10/11 08:29:49
0 2020/10/11 08:29:56
0 2020/10/11 08:30:03
0 2020/10/11 08:30:08
OEM
OEM
0 2020/10/11 08:37:21
0 2020/10/11 08:37:28
Willcox states they a picture on the wall for their techs to use when doing the replacement, look at the wiring order closely
Willcox states they a picture on the wall for their techs to use when doing the replacement, look at the wiring order closely
0 2020/10/11 08:37:34
You may have a different model, if so give Edelbrock a call
You may have a different model, if so give Edelbrock a call
0 2020/10/14 07:11:48
The left side of the tool is 1/2 inch wide, and the metal thickness is approx 2 credit cards. My screwdrivers, were too thick.
The left side of the tool is 1/2 inch wide, and the metal thickness is approx 2 credit cards. My screwdrivers, were too thick.
0 2020/10/14 07:51:41
Ensure that your 72 Fuse Box is the same as my 72
Ensure that your 72 Fuse Box is the same as my 72
0 2020/10/16 13:31:21
Your page number may be different as this is a 1973 Service Manual.
Your page number may be different as this is a 1973 Service Manual.
0 2020/10/16 17:13:43
The nail will Make a perfect depression in the center of the rivet.
The nail will Make a perfect depression in the center of the rivet.
0 2020/10/25 06:51:18
0 2020/10/25 07:02:10
0 2020/10/25 07:02:17