CorvetteForum - Chevrolet Corvette Forum Discussion
0 2014/09/09 15:44:59
0 2014/09/09 15:45:07
0 2014/09/11 08:01:58
0 2014/09/11 08:02:58
0 2014/09/11 08:03:05
0 2014/09/27 19:28:15
0 2014/09/27 19:28:21
0 2014/10/25 23:48:33
0 2014/10/25 23:48:37
0 2014/10/25 23:48:42
0 2014/10/25 23:48:47
this is from the air system right? should i clean this thing or do something with it while its out?
this is from the air system right? should i clean this thing or do something with it while its out?
0 2014/10/25 23:48:55
0 2014/10/29 10:24:48
0 2014/10/29 10:24:53
0 2014/11/24 16:22:29
0 2014/11/24 16:22:35
should i remove this plate because im going to get flakes of cork on it in removing the old gasket.
should i remove this plate because im going to get flakes of cork on it in removing the old gasket.
0 2014/11/24 16:22:46
0 2014/11/24 16:22:56
a previous owner cracked both of these gas lines and there is an indent in them consistent with having a jack stuck under them. i presume they are return lines?
a previous owner cracked both of these gas lines and there is an indent in them consistent with having a jack stuck under them. i presume they are return lines?
0 2014/11/24 16:23:04
fairly clean? there was zero metal. a bit of red rubber from some gasket i presume.
fairly clean? there was zero metal. a bit of red rubber from some gasket i presume.
0 2014/11/24 16:23:12
cleaning this thing really sucked
cleaning this thing really sucked
0 2014/11/24 20:26:51
0 2014/11/24 20:27:02
i just held this in my hand, and dipped it in oil. that stopped any scratches and didn't allow the cork to fluff about in the air because it was caked in oil. worked good.
i just held this in my hand, and dipped it in oil. that stopped any scratches and didn't allow the cork to fluff about in the air because it was caked in oil. worked good.
0 2014/11/24 20:27:15
this is what i used to hammer my pry bar thingy that was in my screw driver set.
this is what i used to hammer my pry bar thingy that was in my screw driver set.
0 2014/11/26 20:47:41
my pry bar thingy. worked well.
my pry bar thingy. worked well.
0 2014/11/26 20:48:02
0 2014/11/27 06:49:23
0 2014/11/27 06:49:35
0 2014/11/27 06:49:44
0 2014/11/27 06:49:50
0 2014/11/27 06:50:02
0 2014/11/29 06:23:37
0 2014/11/29 06:23:44
0 2014/11/29 06:23:49
notice the 1/8 inch holes drilled on the flange of the tstat. do this.
notice the 1/8 inch holes drilled on the flange of the tstat. do this.
0 2014/12/16 13:07:16
0 2014/12/16 20:23:32
0 2014/12/16 20:23:33
0 2014/12/16 20:26:44
0 2014/12/16 20:26:58
0 2014/12/16 20:27:07
these 2 lines are rear driver side and smell fuelly.
these 2 lines are rear driver side and smell fuelly.
0 2014/12/28 22:43:18