CorvetteForum - Chevrolet Corvette Forum Discussion
0 2014/12/24 23:15:34
0 2015/05/10 21:13:29
0 2015/05/10 21:23:25
0 2015/05/10 21:30:18
0 2015/05/10 21:31:29
0 2015/05/10 21:34:18
This is from the instalation guide for Wartsila 20 engine of about 1600 HP. HT is High Temp, or the jacket water side, the LT is for the intercooler side, with both systems being independant of each other. #7 is the Orifice , or Ajustment Valves we use to slow the flow. I'm not sure what the need for a second one would be when the Thurmostat is closed and the water is by passing the cooler but the call for one.
This is from the instalation guide for Wartsila 20 engine of about 1600 HP. HT is High Temp, or the jacket water side, the LT is for the intercooler side, with both systems being independant of each other. #7 is the Orifice , or Ajustment Valves we use to slow the flow. I'm not sure what the need for a second one would be when the Thurmostat is closed and the water is by passing the cooler but the call for one.
0 2015/11/08 10:48:27
0 2015/11/08 11:01:46
0 2015/12/10 22:39:24
0 2016/04/25 23:02:23
0 2016/04/25 23:05:52
0 2016/09/10 20:21:00
0 2016/09/10 20:22:09
0 2016/10/20 20:04:03
0 2016/12/04 08:24:06
0 2016/12/04 08:24:55
0 2016/12/04 08:27:04
0 2016/12/04 08:27:40
0 2016/12/04 08:55:39
Fresh from the Ball Hone
Fresh from the Ball Hone
0 2016/12/04 08:56:49
Piston Rods back in. Had to remove one Stud for each Cylinder to allow Ring Compressor to fit in there.
Piston Rods back in. Had to remove one Stud for each Cylinder to allow Ring Compressor to fit in there.
0 2016/12/04 08:58:24
Crank all looks good. I have decided to replace the bearings anyway.
Crank all looks good. I have decided to replace the bearings anyway.
0 2016/12/04 09:00:44
I have never dealt with a Rev Kit before but by loosening a couple of Studs I was able to pull the Heads down over them.
I have never dealt with a Rev Kit before but by loosening a couple of Studs I was able to pull the Heads down over them.
0 2016/12/04 09:02:48
Heads are back on its time to adjust the Valves. Sounds like Comp Cams wants 1 full turn compressing the Lifter. ( Hyd Roller Cam)
Heads are back on its time to adjust the Valves. Sounds like Comp Cams wants 1 full turn compressing the Lifter. ( Hyd Roller Cam)
0 2016/12/04 09:05:56
0 2016/12/04 15:58:45
0 2016/12/04 15:59:55
0 2016/12/04 16:03:12
0 2016/12/04 16:03:52
0 2016/12/04 16:04:52
0 2016/12/04 16:08:36
0 2016/12/04 16:09:11
0 2016/12/04 16:10:10
0 2017/01/04 19:31:57
0 2017/05/21 20:14:19
0 2020/01/10 20:14:35
0 2020/01/10 21:09:29
0 2020/01/10 21:57:48
The old Block is going from .030 to .060.
The old Block is going from .030 to .060.
0 2020/02/03 19:05:10
0 2020/02/03 22:00:30
0 2020/02/03 22:06:26