CorvetteForum - Chevrolet Corvette Forum Discussion
How do I remove the part still in the engine block? It seems to be stuck in the block.
How do I remove the part still in the engine block? It seems to be stuck in the block.
0 2016/11/15 04:33:36
0 2016/11/15 07:07:51
0 2016/11/15 07:08:41
0 2016/11/15 07:10:05
0 2016/11/15 15:44:20
0 2016/11/20 12:40:00
Do I use sealant on this type of thermostat gasket?
Do I use sealant on this type of thermostat gasket?
0 2016/11/24 13:52:31
0 2016/11/26 06:59:38
0 2016/11/26 07:20:01
0 2016/11/26 07:25:52
What is the hole in the choke housing with the white stuff in it? This is a 670 Holley Avenger which I bought new and has been used on my car for the last 45000 miles. I never noticed the white stuff before. Carb works fine.
What is the hole in the choke housing with the white stuff in it? This is a 670 Holley Avenger which I bought new and has been used on my car for the last 45000 miles. I never noticed the white stuff before. Carb works fine.
0 2016/11/26 07:32:45
Is this a 8.5 or 6.5 power valve? I wrote 6.5 in my log book, but with 11" of vacuum at idle I thought I would have put in 8.5 power valve. Dave
Is this a 8.5 or 6.5 power valve? I wrote 6.5 in my log book, but with 11" of vacuum at idle I thought I would have put in 8.5 power valve. Dave
0 2016/11/26 08:17:49
0 2016/11/30 13:33:01
0 2016/11/30 13:34:29
0 2016/11/30 13:38:37
0 2016/11/30 13:39:17
0 2016/11/30 15:32:58
65 327 4 spd. Clutch cross shaft.The frame side has a felt seal and the engine side has a rubber seal that was pushed out and distorted. I ordered new seals and recieved 2 felt seals. Does the engine side use both felt and rubber seal. Or do I get rid of the rubber one and just use the 2 felt seals? Dave
65 327 4 spd. Clutch cross shaft.The frame side has a felt seal and the engine side has a rubber seal that was pushed out and distorted. I ordered new seals and recieved 2 felt seals. Does the engine side use both felt and rubber seal. Or do I get rid of the rubber one and just use the 2 felt seals? Dave
0 2016/12/05 08:10:15
0 2016/12/28 11:49:12
65 327 4 spd. Firewall below heater. Yellow arrows. 4 - 1 inch holes. Red arrow. 1 - 1/4 inch hole.
65 327 4 spd. Firewall below heater. Yellow arrows. 4 - 1 inch holes. Red arrow. 1 - 1/4 inch hole.
0 2016/12/28 12:20:43
3 holes beside heater cover. Top hole has bolt in it. This car has aftermarket Vintage Air a/c.
3 holes beside heater cover. Top hole has bolt in it. This car has aftermarket Vintage Air a/c.
0 2016/12/28 12:26:15
Large hole behind ballist resistor.
Large hole behind ballist resistor.
0 2016/12/28 12:31:34
0 2016/12/29 15:17:28
4 more holes in passager inner fender. They don't line up for the voltage regulator, nor is there any voltage reg. mounting holes in the rad support at all. It's on the driver side inner fender. Where should the voltage reg be on what I assume is a '65 327 300hp non air car. Battery on drivers side.
4 more holes in passager inner fender. They don't line up for the voltage regulator, nor is there any voltage reg. mounting holes in the rad support at all. It's on the driver side inner fender. Where should the voltage reg be on what I assume is a '65 327 300hp non air car. Battery on drivers side.
0 2016/12/29 15:27:58
0 2016/12/29 15:40:58
This is the way it was when I bought the car. But I have seen pictures where are the regulator is further back beside the alternator on the inner fender. Also no holes in the rad support 4 the voltage regulator.
This is the way it was when I bought the car. But I have seen pictures where are the regulator is further back beside the alternator on the inner fender. Also no holes in the rad support 4 the voltage regulator.
0 2016/12/29 15:42:40
Two holes filled under Fender cross flag emblems.
Two holes filled under Fender cross flag emblems.
0 2016/12/29 15:48:00
Two holes filled under cross flag Fender emblems.
Two holes filled under cross flag Fender emblems.
0 2016/12/29 15:49:56
325 small shaft case
325 small shaft case
0 2017/01/06 04:03:22
Passager side speedo
Passager side speedo
0 2017/01/06 04:05:35
0 2017/01/06 04:07:01
Aug-15 ? What does the sideways 8 mean?
Aug-15 ? What does the sideways 8 mean?
0 2017/01/06 04:09:15
Drivers side serial # 4100111. If this is a corvette trans, should it not be 4S100111 or 4A100111?
Drivers side serial # 4100111. If this is a corvette trans, should it not be 4S100111 or 4A100111?
0 2017/01/06 04:11:58
'65 327 4spd. Built Nov '64. I would think this would be done at the factory, an error? It looks like the the 6 was flattened out and restamped with the 7. Serial # S101566
'65 327 4spd. Built Nov '64. I would think this would be done at the factory, an error? It looks like the the 6 was flattened out and restamped with the 7. Serial # S101566
0 2017/01/06 04:53:32
Is this the rounded boss
Is this the rounded boss
0 2017/01/06 15:49:22
0 2017/01/06 15:51:22
0 2017/01/06 15:54:01
0 2017/01/08 18:33:04
0 2017/01/08 18:33:31
0 2017/02/01 08:35:08