CorvetteForum - Chevrolet Corvette Forum Discussion
Rear section riser is good.
Rear section riser is good.
0 2020/03/29 04:45:57
Rear compartment is for a coupe, wheel well covers for a convertible don't allow access behind the spring assembly. Will make it work one way or another.
Rear compartment is for a coupe, wheel well covers for a convertible don't allow access behind the spring assembly. Will make it work one way or another.
0 2020/03/29 04:45:31
Front carpet fits fine. Excess material will be trimmed later.
Front carpet fits fine. Excess material will be trimmed later.
0 2020/03/29 04:45:15
Last picture of taped foam flooring. Next I test fit the carpet right over the foam.
Last picture of taped foam flooring. Next I test fit the carpet right over the foam.
0 2020/03/29 04:42:36
When you are doing your test fitment it does not have to be fancy to be informative or effective. What we are doing here is learning and making plans for installation.
When you are doing your test fitment it does not have to be fancy to be informative or effective. What we are doing here is learning and making plans for installation.
0 2020/03/29 04:41:30
Temporary taping to see how it all fits.
Temporary taping to see how it all fits.
0 2020/03/29 04:40:50
Dry fit foam with blue painters tape holding seams because I don't have my seam tape here yet. Still on order.
Dry fit foam with blue painters tape holding seams because I don't have my seam tape here yet. Still on order.
0 2020/03/29 04:39:58
Yep, a third picture of the painted area. Note I painted the cross brace brackets and bolts after removing them and they are re-installed here now.
Yep, a third picture of the painted area. Note I painted the cross brace brackets and bolts after removing them and they are re-installed here now.
0 2020/03/29 04:38:12
Second picture of painted dash area.
Second picture of painted dash area.
0 2020/03/29 04:37:33
I taped off this area of the interior so I could clean and paint the dash to get surface rusted areas protected.
I taped off this area of the interior so I could clean and paint the dash to get surface rusted areas protected.
0 2020/03/29 04:35:25
0 2020/03/28 13:47:10
0 2020/03/28 13:46:47
0 2020/03/28 13:46:20
0 2020/03/28 13:46:12
0 2020/03/28 13:45:57
0 2020/03/24 15:38:55
0 2020/03/24 15:38:37
0 2020/03/24 15:38:01
IS-108
IS-108
0 2020/03/22 08:54:54
IS-109
IS-109
0 2020/03/22 08:54:29
IS-207B
IS-207B
0 2020/03/22 08:53:58
IS-365
IS-365
0 2020/03/22 08:53:26
IS-374
IS-374
0 2020/03/22 08:53:02
IS-373
IS-373
0 2020/03/22 08:52:39
IS-372
IS-372
0 2020/03/22 08:52:17
IS-320
IS-320
0 2020/03/22 08:51:50
IS-349
IS-349
0 2020/03/22 08:51:24
IS-420R
IS-420R
0 2020/03/22 08:50:56
IS-420L
IS-420L
0 2020/03/22 08:50:13
IS-302R
IS-302R
0 2020/03/22 08:49:29
IS-302L
IS-302L
0 2020/03/22 08:49:02
IS-380
IS-380
0 2020/03/22 08:48:32
IS-301
IS-301
0 2020/03/22 08:47:55
IS-315
IS-315
0 2020/03/22 08:47:21
This is the original steering column that Gordon rebuilt for me. It looks new and all bearings are now in good shape as are the harnesses. Ready for installation and service.
This is the original steering column that Gordon rebuilt for me. It looks new and all bearings are now in good shape as are the harnesses. Ready for installation and service.
0 2020/03/22 07:20:48
These are the front extension washers which were quite corroded and rusty. They are now better than original and I hope will last for years to come.
These are the front extension washers which were quite corroded and rusty. They are now better than original and I hope will last for years to come.
0 2020/03/22 07:19:53
These are the lower seat belt guides which are original to the car. They were quite corroded and nasty so I had them powder coated, again for durability.
These are the lower seat belt guides which are original to the car. They were quite corroded and nasty so I had them powder coated, again for durability.
0 2020/03/22 07:18:49
This lower steering bracket is used in the engine bay with the steering column. I had it powder coated for durability as well.
This lower steering bracket is used in the engine bay with the steering column. I had it powder coated for durability as well.
0 2020/03/22 07:18:02
This lower shift retainer brace be installed over my new rubber shift boot to keep the weather elements out of the compartment from underneath. I had it powder coated to make it as durable as possible.
This lower shift retainer brace be installed over my new rubber shift boot to keep the weather elements out of the compartment from underneath. I had it powder coated to make it as durable as possible.
0 2020/03/22 07:16:44
These two brackets cleaned up very nicely and now you can see the part numbers on the finished parts. These will be used when I marry the body back onto the chassis.
These two brackets cleaned up very nicely and now you can see the part numbers on the finished parts. These will be used when I marry the body back onto the chassis.
0 2020/03/22 07:15:52