Cup Holder for C2
#1
Racer
Thread Starter
Cup Holder for C2
Does anyone on the forum have the snap on console/cup coin holder for their C2's, if so how do you folks like them. Thinking about purchasing one. Thanks Ditch.
#2
Drifting
We have one in our '64 and like it. I got ours from a forum member that decided not to use it.
When I first put it in, I didn't like the looks of it, so I cut some hard felt inserts to go in the openings to make it look more finished:
It does a good job of holding my phone, garage door remote, etc. but the cup holders are so shallow I would not trust them to hold a drink while I was driving though.
Todd
When I first put it in, I didn't like the looks of it, so I cut some hard felt inserts to go in the openings to make it look more finished:
It does a good job of holding my phone, garage door remote, etc. but the cup holders are so shallow I would not trust them to hold a drink while I was driving though.
Todd
#3
Racer
Thread Starter
We have one in our '64 and like it. I got ours from a forum member that decided not to use it.
When I first put it in, I didn't like the looks of it, so I cut some hard felt inserts to go in the openings to make it look more finished:
It does a good job of holding my phone, garage door remote, etc. but the cup holders are so shallow I would not trust them to hold a drink while I was driving though.
Todd
When I first put it in, I didn't like the looks of it, so I cut some hard felt inserts to go in the openings to make it look more finished:
It does a good job of holding my phone, garage door remote, etc. but the cup holders are so shallow I would not trust them to hold a drink while I was driving though.
Todd
#4
Tech Contributor
#5
Melting Slicks
I have the clear plastic model, It's junk.
#6
Racer
Thread Starter
The following 5 users liked this post by edub63vette:
1960 (04-28-2022),
66rdstr (04-29-2022),
dcamick (04-28-2022),
keith ragan (04-29-2022),
marshal135 (04-28-2022)
The following users liked this post:
1960 (04-28-2022)
#9
Pro
I have the same one Todd has in my 65 Convertible, it is very handy and has two different size cup holders. I like what Todd did to dress it up, think I will do something like that also.
George
George
#11
Race Director
Member Since: Mar 2009
Location: Canada's capital
Posts: 19,777
Received 4,583 Likes
on
2,157 Posts
2020 Corvette of the Year Finalist (appearance mods)
C1 of Year Finalist (appearance mods) 2019
Frank, Mdyearvette, has a nice one in his C2, only Franks keeps a bottle of whiskey in his.....
Post that pic Knuckles.......?
Post that pic Knuckles.......?
#12
Enjoy while you can.
Member Since: May 2008
Location: 10th District Court OHIO
Posts: 17,172
Received 2,688 Likes
on
1,274 Posts
Ohio Events Coordinator
2023 C8 of the Year Finalist - Unmodified
2022 C2 of the Year Finalist - Unmodified
C2 of Year Finalist (stock) 2019
St. Jude Donor '14-'15-'16-'17-‘18-'19-'20-'21-'22-'23-'24
Oh Frank will state he was out on a job, but at his age he just takes longer naps these days so here is the pic .....
The following 2 users liked this post by woodsdesign:
1960 (04-28-2022),
keith ragan (04-29-2022)
#17
Melting Slicks
#18
Pro
I bought one of these at Pep Boys for a 3 bucks or so. A single screw thru my floor carpet right at the left front edge of the right front seat close to the console holds it in place,,,right next to my Halon extinguisher. Does an excellent job of holding one of those aluminum type thermos bottles or just about any other container. The adjustable "clamp" like device keeps the container tight in place. Positioned where it is in my C1 puts it right where my right hand can easily reach it. Velcro also comes with it to affix it to the floor if you don't want to drill a tiny hole. Called a Spillmaster Euro Junior,,,google it.
http://www.muchmakersfleaemporium.co...everage-holder
It is not even noticeable on the floor when no container is in place. Comes out in 30 seconds with a screwdriver if you wish to remove. Anything else that I've used over the years just doesn't work, is unsafe or looks tacky.
http://www.muchmakersfleaemporium.co...everage-holder
It is not even noticeable on the floor when no container is in place. Comes out in 30 seconds with a screwdriver if you wish to remove. Anything else that I've used over the years just doesn't work, is unsafe or looks tacky.
Last edited by Sxrxrnr; 05-24-2011 at 01:11 AM.
#19
Enjoy while you can.
Member Since: May 2008
Location: 10th District Court OHIO
Posts: 17,172
Received 2,688 Likes
on
1,274 Posts
Ohio Events Coordinator
2023 C8 of the Year Finalist - Unmodified
2022 C2 of the Year Finalist - Unmodified
C2 of Year Finalist (stock) 2019
St. Jude Donor '14-'15-'16-'17-‘18-'19-'20-'21-'22-'23-'24