This was EXHAUSTING!
Thread Starter
Melting Slicks
Joined: Aug 2004
Posts: 2,241
Likes: 6
From: Arizona
This was EXHAUSTING!
After months of indecision, I finally purchased the exhaust I'm going to put on this car.
I have a difficult time making up my mind but, went with Paragon's
2-1/2" aluminzed under car exhaust, with OFF-Road mufflers, and Jet-Hot's Sterling finish Hooker headers.
I have a difficult time making up my mind but, went with Paragon's
2-1/2" aluminzed under car exhaust, with OFF-Road mufflers, and Jet-Hot's Sterling finish Hooker headers.
Le Mans Master
Joined: Jul 2000
Posts: 8,506
Likes: 3
From: Calhoun, GA_______ Let It Rock
Too pretty a chassis to stick a body on it. Drive it like it is ! 
Is that an Edelbrock crate motor ? Have you heard that exhaust system ? I would like to wake mine up a little. It has headers, but I'm unsure of the mufflers.
Is that an Edelbrock crate motor ? Have you heard that exhaust system ? I would like to wake mine up a little. It has headers, but I'm unsure of the mufflers.
Last edited by Grey Ghost; Apr 22, 2006 at 10:22 PM.
Thread Starter
Melting Slicks
Joined: Aug 2004
Posts: 2,241
Likes: 6
From: Arizona
Grey Ghost,
All the components are Edelbrock but it is not Edelbrock's crate motor.
No I have not heard the exhaust but I figured at only $320 for the entire Paragon system, I could afford to change the mufflers a couple of times if I didn't like them.
I really am taking my time...probably because I don't want to cover the chassis.
I get alot of walk by's admiring it. (I live really close to the street).
I have done more since the photo, hard/braided fuel lines etc.
All the components are Edelbrock but it is not Edelbrock's crate motor.
No I have not heard the exhaust but I figured at only $320 for the entire Paragon system, I could afford to change the mufflers a couple of times if I didn't like them.
I really am taking my time...probably because I don't want to cover the chassis.
I get alot of walk by's admiring it. (I live really close to the street).I have done more since the photo, hard/braided fuel lines etc.
Drifting
Joined: Feb 2006
Posts: 1,840
Likes: 29
From: Towaco NJ
Originally Posted by mgsouthard
After months of indecision, I finally purchased the exhaust I'm going to put on this car.
I have a difficult time making up my mind but, went with Paragon's
2-1/2" aluminzed under car exhaust, with OFF-Road mufflers, and Jet-Hot's Sterling finish Hooker headers.
I have a difficult time making up my mind but, went with Paragon's
2-1/2" aluminzed under car exhaust, with OFF-Road mufflers, and Jet-Hot's Sterling finish Hooker headers.
Thread Starter
Melting Slicks
Joined: Aug 2004
Posts: 2,241
Likes: 6
From: Arizona
Originally Posted by vetrod62
There must be some kind of filter on my PC. I still do not see the headers, off road mufflers or aluminzed pipes on the attached file. I promise not to ask about the belt drive.
I ordered them today! Expect them in the first week of May.
I talked to March Systems and they said they didn't see a problem with the belt contact, and refered me to their drawings.
Many of their drawings of different configurations don't look alot better than mine.
March did ask if I had tried to move the Alt bracket closer to the block, but I have not done any thing with it yet. I not too concerned, because I'll make it right myself if I have too.
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
Top 10 Most Expensive Corvettes Ever Sold on Bring A Trailer
Brett Foote
10 Things Every Corvette Owner Needs (2026 Edition)
Michael S. Palmer
8 Most "Only Corvette Owners Understand" Quirks and Problems
Pouria Savadkouei
10 Reasons the C6 Z06 is Still A Performance Benchmark After 20 Years
Joe Kucinski
How Much Horsepower Every Corvette Engine "LOST" in 1972
Joe Kucinski
Top 10 DOs and DON'Ts for Protecting Your Convertible Top!
Michael S. Palmer
Top 10 Most Explosive Corvettes Ever Made: Power-to-Weight Ratio Ranked!
Joe Kucinski
150 hp to 1,250 hp: Every Corvette Generation Compared by the Specs That Matter
Joe Kucinski