trans cooling lines
Thread Starter
Instructor
Joined: Feb 2006
Posts: 143
Likes: 0
From: floral city fl
trans cooling lines
i need some help!!! my trans cooling lines on my 75 vette rubbed a hole in each other. so i thought it should not be to hard to replace two lines. my question is where the line enter the trans i cannot get a wrench up in that tight area. now there is a canister on the side of the trans with a line that runs up topside. do i have to remove that canister to get to the lines or is there a tool out there to get to remove the nuts on the trans lines. any help would be great.
thanks scott
thanks scott
Race Director
Joined: Sep 2004
Posts: 11,874
Likes: 263
From: Arlington Va Current ride 04 vert, previous vettes: 69 vert, 77 resto mod
its a tight spot but if you lie under the car there is one spot that a small open end wrench will fit on and you will get a 1/4 turn....it is a PITA
Melting Slicks
Joined: May 2002
Posts: 2,717
Likes: 121
From: Sulphur LA
St. Jude Donor '05-'06,'11,'13-'14,'16,'18,'19,'24, '25
Be very careful working around the detent cable I broke a new one right were it enters the trans while working on my cooling lines.
Neal
Neal
Melting Slicks
Joined: Jul 2004
Posts: 2,577
Likes: 2
From: Long Island New York
Originally Posted by bobs77vet
its a tight spot but if you lie under the car there is one spot that a small open end wrench will fit on and you will get a 1/4 turn....it is a PITA
Bob's right, I just did mine, it can be done, but a PITA.
Race Director
Joined: Jul 2004
Posts: 12,711
Likes: 329
From: Scottsdale Arizona
Originally Posted by Artsvette73
A little more work but you remove the crossmember and lower the trans. Just be carefull of the distributer cap when you lower it.
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
5 Best & 5 Worst Corvette Daily Drivers
Joe Kucinski
The Headlights of Every Corvette Generation Explained
Joe Kucinski
5 Best & 5 Most Overrated Corvette Track Packages of All Time!
Joe Kucinski
Every 2027 Corvette Engine Explained
Joe Kucinski
Designer Imagines A Corvette That Looks More Like a Corvette Than the Corvette
Verdad Gallardo
10 Ugly Corvettes That We Still Kinda Love
Joe Kucinski
Top 10 Most Expensive Corvettes Ever Sold on Bring A Trailer
Brett Foote
10 Things Every Corvette Owner Needs (2026 Edition)
Michael S. Palmer
8 Most "Only Corvette Owners Understand" Quirks and Problems
Pouria Savadkouei
Racer
Joined: Sep 2005
Posts: 453
Likes: 1
From: Austin TX
It just took me 6 hours last weekend to get the upper line bent and connected on my 700R4 swap. I went from a TH350 to 700R4. When I removed the TH350 I remember using a crow's foot on an end of a 3/8" rachet with some extentions and wobble head (be careful not to strip threads). After I got the lines bent correctly, this is the same method I used to tighten them back up. I also did the wrench from above by sticking your arm through the top of the tranny/floor and turning it very very slowly.
Burning Brakes
Joined: Feb 2006
Posts: 1,173
Likes: 5
From: Paducah Ky
Originally Posted by Star79
I saw how much room there was to reach the lines and did this.....
...floors are non-original anyway
...floors are non-original anyway
Melting Slicks
Joined: Jul 2004
Posts: 2,577
Likes: 2
From: Long Island New York
Originally Posted by gyopp
removing the cross member should be much easier than removing pass seat, center console, removing carpet, and doing a bubba mod to the floorpan.
Definiately not something I would do to mine.
Melting Slicks
Joined: Apr 2004
Posts: 2,083
Likes: 2
From: Montreal Qc.
Originally Posted by gyopp
removing the cross member should be much easier than removing pass seat, center console, removing carpet, and doing a bubba mod to the floorpan.
Like I said, the floors were replaced before anyway. If there's a problem, the guys on The Forum gave it their blessing first
(okay GSC3 did it before me anyway....)
Last edited by Star79; Oct 28, 2006 at 11:51 PM.
