Corvette Traction Bar?
Thread Starter
Safety Car
Joined: Aug 2000
Posts: 3,909
Likes: 26
From: Clymer PA
Corvette Traction Bar?
What exactly would the benefit of a traction bar be? I was told that it reduces the rear end flex under acceleration. Is it worth the money, or would I be better off spending it else where?
Safety Car
Joined: Dec 1999
Posts: 4,148
Likes: 5
From: Roxbury NJ
Re: Corvette Traction Bar? (bence13_33)
Aren't "traction bars" the bars with the rubber bumpers that prevent a solid axle from twisting upward by bending the perpendicular leaf springs that hold it? Since the Vette is IRS, and the leaf is parallel to the axle, I don't think you would need them.
Thread Starter
Safety Car
Joined: Aug 2000
Posts: 3,909
Likes: 26
From: Clymer PA
Re: Corvette Traction Bar? (Flareside)
Flareside:
Yes, normally for Camaros and what not they are traction bars. For the 'Vette they make a traction bar...it bolts to the rear end and I believe where the rear end support is.
BTW the "rubber bumpers" that you referred to are snubbers :)
Yes, normally for Camaros and what not they are traction bars. For the 'Vette they make a traction bar...it bolts to the rear end and I believe where the rear end support is.
BTW the "rubber bumpers" that you referred to are snubbers :)
Burning Brakes
Joined: Oct 2001
Posts: 1,185
Likes: 0
From: New Wilmington PA
Re: Corvette Traction Bar? (bence13_33)
My understanding if traction bars was that they bolted/clamped to the leaf springs as a measure to decrease squatting during acceleration. They allow a little downward movement but cause the springs to react stiffly at a set height turning the downward motion of the rear into downward force applied to the wheels. A friend of mine uses them on his built 69 Camaro. Car rides like crap but hooks up beautifully off the line. You may be thinking about a 4-link or ladder bar setup. Not positive but I think they are designed to combat rear end flex.
C6 the C5 of tomorrow
Joined: Nov 2000
Posts: 6,665
Likes: 2
From: Twin Cities Minnesota
Re: Corvette Traction Bar? (bence13_33)
It seems to me that by using the crossmember locating discs and a poly front Diff mount there is really no need nor benifit of a traction bar since the diff will not be moving!
Burning Brakes
Joined: Jan 2001
Posts: 1,004
Likes: 16
From: Gainesville, Florida
Re: Corvette Traction Bar? (427V8)
Most traction devices including snubber bars used on leaf spring cars prevent the pinion angle from changing dramatically during acceleration. The Corvette bar does the same thing but it bolts to the bottom of the differential in the rear and to the frame in the front. IMHO the Corvette bar is of questionable worth due to the Corvette's built-in pinion snubber. I would rather spend the money on new top & bottom polyurethane cushions for the pinion snubber.
Mark
[Modified by mdsmith, 6:13 PM 12/16/2001]
Mark
[Modified by mdsmith, 6:13 PM 12/16/2001]
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
Top 10 Most Expensive Corvettes Ever Sold on Bring A Trailer
Brett Foote
10 Things Every Corvette Owner Needs (2026 Edition)
Michael S. Palmer
8 Most "Only Corvette Owners Understand" Quirks and Problems
Pouria Savadkouei
10 Reasons the C6 Z06 is Still A Performance Benchmark After 20 Years
Joe Kucinski
How Much Horsepower Every Corvette Engine "LOST" in 1972
Joe Kucinski
Top 10 DOs and DON'Ts for Protecting Your Convertible Top!
Michael S. Palmer
Top 10 Most Explosive Corvettes Ever Made: Power-to-Weight Ratio Ranked!
Joe Kucinski
150 hp to 1,250 hp: Every Corvette Generation Compared by the Specs That Matter
Joe Kucinski
8 Coolest Corvette Pace Cars (and Replicas) of All Time
Verdad Gallardo
Instructor
Joined: May 2001
Posts: 228
Likes: 0
From: Santa Cruz CA
Re: Corvette Traction Bar? (427V8)
I installed one, it hangs from the bottom of the strut rod mounting plate and uses a 1" steel tube to the forward crossmember. It is in the way of my pipes, so now my pipes rattle. It seems like a crutch that shouldn't be needed if the rearend is well located, but if you consider the torque reaction of the rear end plus all the spring loads, there is a lot of force going through a center section that is really not all that well supported. I suspect that under high torque situations, that thing twists and bends the removable crossmember above severely. I suppose that is why the C4 has a large integral truss to support the rear end. Does the C4 have a long torque arm like the Camaro too?
Anyway, I installed the thing to try and cure some axle hop which turned out to be excessive side yolk end play.
Anyway, I installed the thing to try and cure some axle hop which turned out to be excessive side yolk end play.
Melting Slicks
Joined: May 2001
Posts: 2,215
Likes: 170
From: PA
Re: Corvette Traction Bar? (68427)
This may not help because it is on a C2 but you can look and see home made traction bar and it does help.
http://www.steves65customvette.homestead.com/main.html
http://www.steves65customvette.homestead.com/main.html
