[/IMG]
spark plug wire looms
Drifting
Joined: Sep 2006
Posts: 1,986
Likes: 21
From: Columbus MN
This isn't a very good picture of the wire loom I used to have, but they are anodized blue and mount on the valve cover:
Here are the ball milled wire looms I now:
These are mounted on the block, not the valve covers and match the ball milled ac cover I have now too:
Here are the ball milled wire looms I now:
These are mounted on the block, not the valve covers and match the ball milled ac cover I have now too:
Drifting
Joined: Sep 2006
Posts: 1,986
Likes: 21
From: Columbus MN
There are a number of wire looms with this design available. I had a set but didn't like covering the valve covers. That's why I switched to block-mounted wire looms. The other choice I tried was the inviditual plastic looms that attached to 3 of 4 valve cover bolts on each side.
What look do you want?
What look do you want?
Drifting
Joined: Sep 2006
Posts: 1,986
Likes: 21
From: Columbus MN
HOWEVER, if you like the wire looms mounted on the Vortec center bolts, then go for it. Check flea bay for center bolt wire looms to see what your options are and then shop around. Maybe a C3 Forum sponsor or two have them too and will chime in with their offerings.
Burning Brakes
Joined: May 2006
Posts: 774
Likes: 1
From: Round Rock Texas
Those are the same wire looms I have. What I like about them is that they don't advertise the fact that Vortec heads have center bolts on the valve covers unlike the rest of the SBC world.
HOWEVER, if you like the wire looms mounted on the Vortec center bolts, then go for it. Check flea bay for center bolt wire looms to see what your options are and then shop around. Maybe a C3 Forum sponsor or two have them too and will chime in with their offerings.
HOWEVER, if you like the wire looms mounted on the Vortec center bolts, then go for it. Check flea bay for center bolt wire looms to see what your options are and then shop around. Maybe a C3 Forum sponsor or two have them too and will chime in with their offerings.
Burning Brakes
Joined: May 2006
Posts: 774
Likes: 1
From: Round Rock Texas
Those are the same wire looms I have. What I like about them is that they don't advertise the fact that Vortec heads have center bolts on the valve covers unlike the rest of the SBC world.
HOWEVER, if you like the wire looms mounted on the Vortec center bolts, then go for it. Check flea bay for center bolt wire looms to see what your options are and then shop around. Maybe a C3 Forum sponsor or two have them too and will chime in with their offerings.
HOWEVER, if you like the wire looms mounted on the Vortec center bolts, then go for it. Check flea bay for center bolt wire looms to see what your options are and then shop around. Maybe a C3 Forum sponsor or two have them too and will chime in with their offerings.
Thanks.
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
Every 2027 Corvette Engine Explained
Joe Kucinski
Designer Imagines A Corvette That Looks More Like a Corvette Than the Corvette
Verdad Gallardo
10 Ugly Corvettes That We Still Kinda Love
Joe Kucinski
Top 10 Most Expensive Corvettes Ever Sold on Bring A Trailer
Brett Foote
10 Things Every Corvette Owner Needs (2026 Edition)
Michael S. Palmer
8 Most "Only Corvette Owners Understand" Quirks and Problems
Pouria Savadkouei
10 Reasons the C6 Z06 is Still A Performance Benchmark After 20 Years
Joe Kucinski
How Much Horsepower Every Corvette Engine "LOST" in 1972
Joe Kucinski
Top 10 DOs and DON'Ts for Protecting Your Convertible Top!
Michael S. Palmer
Burning Brakes
Joined: Jan 2006
Posts: 957
Likes: 6
From: Burlington wisconsin
http://www.jegs.com/i/JEGS/555/41000/10002/-1
Last edited by cherrybombc3; Dec 31, 2009 at 10:56 AM.
