1974 clock replacement
Thread Starter
Burning Brakes
Joined: May 2002
Posts: 829
Likes: 0
From: Reisterstown MD
1974 clock replacement
I am looking to replace my clock and don't want to pay big money to buy a refurbished original. What after market clock looks closest to stock and won't cost an arm and a leg?
Thanks,
JimBRO
Thanks,
JimBRO
Team Owner
Joined: Feb 2003
Posts: 30,183
Likes: 313
From: Lake Norman NC
Re: 1974 clock replacement (mayberg)
mayberg, have you ever had your console out or guage cluster?? if not...you need to in order to change the clock, and its not easy and is time consuming.. i've taken out all the stuff so much i could do it blindfolded.
Drifting
Joined: Oct 2000
Posts: 1,825
Likes: 56
From: Shawano WI
Re: 1974 clock replacement (trw)
If you click on the link in my signatue it will take you through step by step. It was on a 70 but your 74 will be very similar once you get the center gauge panel out.
Team Owner
Joined: Dec 2000
Posts: 24,906
Likes: 0
From: Swords Check/Saws Check/Clubs Check/Claws Check/Hatred Check/Anger Check/Murmaid Check/Murder Check
Cruise-In IV Veteran
Cruise-In VI Veteran
Re: 1974 clock replacement (JimBR0)
I switched to quartz about 3 years ago. For the most part it's reliable although it does stop once in a while. :cuss I just have to move the arms back and forth and it'll restart.
Burning Brakes
Joined: Nov 2001
Posts: 1,191
Likes: 1
Re: 1974 clock replacement (Pete79L82)
What are the details to getting the center guage panel out? Is it simply unscrew from the outside, or do I get to contort myself under the dash and remove other interior components?
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
Top 10 Most Expensive Corvettes Ever Sold on Bring A Trailer
Brett Foote
10 Things Every Corvette Owner Needs (2026 Edition)
Michael S. Palmer
8 Most "Only Corvette Owners Understand" Quirks and Problems
Pouria Savadkouei
10 Reasons the C6 Z06 is Still A Performance Benchmark After 20 Years
Joe Kucinski
How Much Horsepower Every Corvette Engine "LOST" in 1972
Joe Kucinski
Top 10 DOs and DON'Ts for Protecting Your Convertible Top!
Michael S. Palmer
Top 10 Most Explosive Corvettes Ever Made: Power-to-Weight Ratio Ranked!
Joe Kucinski
150 hp to 1,250 hp: Every Corvette Generation Compared by the Specs That Matter
Joe Kucinski
8 Coolest Corvette Pace Cars (and Replicas) of All Time
Verdad Gallardo
Drifting
Joined: Jan 2001
Posts: 1,841
Likes: 3
From: Halifax, NS, Canada
Re: 1974 clock replacement (JimBR0)
The clock you have is probably fine. I have not seen one yet that I could not get running in 5 minutes. The problem with them is that there is a set of points inside that energize the winding mechanism. Once the points get dirty then the clock stops. If you are scared to tackle it just mail it to me. I have repaired 6 out of 6 and it has always been the same problem...just clean the points and lubricate the mechanism and it will run for another 3 years or so.
Melting Slicks
Joined: Sep 2000
Posts: 2,406
Likes: 418
From: Chester Virginia
Re: 1974 clock replacement (JimBR0)
Clean the points in the back of the clock, flush the dirt from the movement and the clock will probably run. Did this to mine. I have also got two clocks from cars in the local junkyard as spares if needed later.
Roger
Roger
Drifting
Joined: Jan 2001
Posts: 1,841
Likes: 3
From: Halifax, NS, Canada
Re: 1974 clock replacement (mvftw)
Is contact cleaner Ok to clean? And what is a good lube for the clock?
Drifting
Joined: Jul 2002
Posts: 1,944
Likes: 20
From: The only Corvettes in Highett Victoria
Re: 1974 clock replacement (JimBR0)
Dear JimBRO,
I bought a quartz kit from Mid America a few years ago and the hardest part was getting the instruction video converted from NTSC to PAL so that I could see it. As long as you follow the video instructions , you should do fine. I can't comment on the cleaning bit, but the thought of repeating the job every couple of years with 30 years old parts makes the modern quartz conversion look the better option. :cheers:
Regards from Down Under
aussiejohn
I bought a quartz kit from Mid America a few years ago and the hardest part was getting the instruction video converted from NTSC to PAL so that I could see it. As long as you follow the video instructions , you should do fine. I can't comment on the cleaning bit, but the thought of repeating the job every couple of years with 30 years old parts makes the modern quartz conversion look the better option. :cheers:
Regards from Down Under
aussiejohn
