FS: 86, 89, 90, 94, 96 parts
#81
Le Mans Master
Thread Starter
#84
Advanced
For my 96 I’m needing a brake master cylinder, the passenger side a/c outlet, and the snap on plastic cover from the turn signal lever area of the column...any help?
thanks!
thanks!
#86
Le Mans Master
Thread Starter
For my 96 I’m needing a brake master cylinder,
i do have a master cylinder and it is full of fluid.
the passenger side a/c outlet,
i just saw the surround and a couple of the vents. i will have to look for the complete assembly.
and the snap on plastic cover from the turn signal lever area of the column.
i purchased a brand new one and never installed it
..any help?
thanks!
i do have a master cylinder and it is full of fluid.
the passenger side a/c outlet,
i just saw the surround and a couple of the vents. i will have to look for the complete assembly.
and the snap on plastic cover from the turn signal lever area of the column.
i purchased a brand new one and never installed it
..any help?
thanks!
#87
Le Mans Master
Thread Starter
#89
Advanced
Member Since: Jul 2014
Location: Hendersonville tn
Posts: 70
Likes: 0
Received 0 Likes
on
0 Posts
#91
Le Mans Master
Thread Starter
#94
Tell me about the crank and block:
The block is a 1-peice RMS right. It says pistons and rods come with it. a 350 uses a 5.7" Rod, do the pistons have a smaller squish height to compensate? What is the piston volume above or below the deck on a standard 350 SBC. Any miles on the block since Machining?
Is the crank new? Has it been balanced?
How much to ship to 35758
The block is a 1-peice RMS right. It says pistons and rods come with it. a 350 uses a 5.7" Rod, do the pistons have a smaller squish height to compensate? What is the piston volume above or below the deck on a standard 350 SBC. Any miles on the block since Machining?
Is the crank new? Has it been balanced?
How much to ship to 35758
Last edited by auburn2; 04-23-2019 at 08:53 PM.
#95
Le Mans Master
Thread Starter
tell me about the crank and block:
The block is a 1-peice rms right. right it says pistons and rods come with it. A 350 uses a 5.7" rod, do the pistons have a smaller squish height to compensate? What is the piston volume above or below the deck on a standard 350 sbc. Any miles on the block since machining?
l98 roller block, line bored, decked, bored .035, arp studs and wiseco forged pistons using 6.0 rods. $125. No rods come with this block, you will have to furnish your own 6.0 rods
is the crank new? Has it been balanced?
a used chevrolet performance 3.48 stroke forged steel 1 piece rear main crankshaft, standard mains and rods, knife edged and balanced to 1750 bob weight. $125
how much to ship to 35758
The block is a 1-peice rms right. right it says pistons and rods come with it. A 350 uses a 5.7" rod, do the pistons have a smaller squish height to compensate? What is the piston volume above or below the deck on a standard 350 sbc. Any miles on the block since machining?
l98 roller block, line bored, decked, bored .035, arp studs and wiseco forged pistons using 6.0 rods. $125. No rods come with this block, you will have to furnish your own 6.0 rods
is the crank new? Has it been balanced?
a used chevrolet performance 3.48 stroke forged steel 1 piece rear main crankshaft, standard mains and rods, knife edged and balanced to 1750 bob weight. $125
how much to ship to 35758
#98
Le Mans Master
Thread Starter
these were not off the shelf pistons so there is not a part number from wiseco. they are the same spec as an 89 piston only the dish is .05 shallower. it raised my compression up about a 1/2 point.
#99
Le Mans Master
Thread Starter
#100