F/S TPI/L98 stainless steel bolt set + special ball-end hex driver
#41
Instructor
Re: F/S TPI/L98 stainless steel bolt set + special ball-end hex driver (CentralCoaster)
I want in on this, let me know if a set is available for me. paypal ready.
email: BodyLogix@bellsouth.net
phone:772.284.4746 Gary.
email: BodyLogix@bellsouth.net
phone:772.284.4746 Gary.
#42
Le Mans Master
Member Since: Jul 2002
Location: Alive and well in Burlington NC
Posts: 5,818
Likes: 0
Received 1 Like
on
1 Post
Re: F/S TPI/L98 stainless steel bolt set + special ball-end hex driver (CentralCoaster)
Just so you guys know, I'm not making any money on this. I marked up the last sets to $1.50 over cost. I'll never get rich at this rate! :lol::smash:
#43
Team Owner
Thread Starter
Member Since: May 2002
Location: San Diego , CA Double Yellow DirtBags 1985..Z51..6-speed
Posts: 24,337
Likes: 0
Received 17 Likes
on
16 Posts
Re: F/S TPI/L98 stainless steel bolt set + special ball-end hex driver (Steel Blue 91)
It's worth the $1.50 just thinking of you sitting on the floor, going through those 1500 bolts.... :lolg: :jester
#44
Team Owner
Thread Starter
Member Since: May 2002
Location: San Diego , CA Double Yellow DirtBags 1985..Z51..6-speed
Posts: 24,337
Likes: 0
Received 17 Likes
on
16 Posts
Re: F/S TPI/L98 stainless steel bolt set + special ball-end hex driver (CentralCoaster)
Chris, I got your check and your set will be shipped out Monday via Fedex insured ground (2-4 days).
Looks like there's 5 more that want a set already. I'm going to be out of town pretty much until May 9th... but I could make up some more sets.
I'll tell you what, if I can get another set of 9 buyers, I'll do another order. :yesnod: This next time around, I'd like to include 12 allen bolts for the intake base, and two more allen drivers. This would bump it up another 10 or 12 bucks though. I haven't figured out the details yet... I'll do that when I get back on the 9th.
Looks like there's 5 more that want a set already. I'm going to be out of town pretty much until May 9th... but I could make up some more sets.
I'll tell you what, if I can get another set of 9 buyers, I'll do another order. :yesnod: This next time around, I'd like to include 12 allen bolts for the intake base, and two more allen drivers. This would bump it up another 10 or 12 bucks though. I haven't figured out the details yet... I'll do that when I get back on the 9th.
#45
Instructor
Member Since: Feb 2003
Location: Hilo Hawaii
Posts: 207
Likes: 0
Received 0 Likes
on
0 Posts
Re: F/S TPI/L98 stainless steel bolt set + special ball-end hex driver (CentralCoaster)
Do you have a list of all the sizes i'd like to put together a grade 8 set.
#46
Team Owner
Thread Starter
Member Since: May 2002
Location: San Diego , CA Double Yellow DirtBags 1985..Z51..6-speed
Posts: 24,337
Likes: 0
Received 17 Likes
on
16 Posts
Re: F/S TPI/L98 stainless steel bolt set + special ball-end hex driver (JYAMZE)
IM'd you.
Also, class 12.9 is the metric equivalent of grade 8 standard. The stock bolts are 10.9... ~grade 5.
Also, class 12.9 is the metric equivalent of grade 8 standard. The stock bolts are 10.9... ~grade 5.
#47
Intermediate
Member Since: Jan 2002
Location: South Charleston Ohio
Posts: 43
Likes: 0
Received 0 Likes
on
0 Posts
Re: F/S TPI/L98 stainless steel bolt set + special ball-end hex driver (CentralCoaster)
Put me on your next list of buyers. It would be great to get the additional 12 bolts for the intake. When and if you do another group purchase let me know at bbenn1961@aol.com so I can send you the money. :hurray:
#48
Instructor
Member Since: Dec 2003
Location: Freehold New Jersey
Posts: 211
Likes: 0
Received 0 Likes
on
0 Posts
Re: F/S TPI/L98 stainless steel bolt set + special ball-end hex driver (BBenn1961)
:party: Screws came in today, time to get busy!!!
Kevin, did you pack and mark all the little baggies? :crazy:
I REALLY feel guilty now,
KEVIN IS "THE" MAN :flag
Kevin, did you pack and mark all the little baggies? :crazy:
I REALLY feel guilty now,
KEVIN IS "THE" MAN :flag
#49
Le Mans Master
Re: F/S TPI/L98 stainless steel bolt set + special ball-end hex driver (fmrff)
:party:
KEVIN IS "THE" MAN :flag
KEVIN IS "THE" MAN :flag
I haven't got to see mine yet since I am on the west side of the state, but I Im'ed Kevin asking he could post a pic so we could sort and make sure they were all there...he replied he had already labled and bagged them!!!
It is awesome, man I can't want to get started on this engine!!!!
#50
Team Owner
Re: F/S TPI/L98 stainless steel bolt set + special ball-end hex driver (USAsOnlyWay)
My screws arrived!!! Thanks! :thumbs:
you da man!!!!!!!!!!!!!! :party: :party: :party:
you da man!!!!!!!!!!!!!! :party: :party: :party:
#51
Drifting
Re: F/S TPI/L98 stainless steel bolt set + special ball-end hex driver (bogus)
My screws arrived!!! Thanks! :thumbs:
you da man!!!!!!!!!!!!!! :party: :party: :party:
you da man!!!!!!!!!!!!!! :party: :party: :party:
#52
Team Owner
Thread Starter
Member Since: May 2002
Location: San Diego , CA Double Yellow DirtBags 1985..Z51..6-speed
Posts: 24,337
Likes: 0
Received 17 Likes
on
16 Posts
Re: F/S TPI/L98 stainless steel bolt set + special ball-end hex driver (ductape)
One thing I realized after putting all these together, I should have used shorter fuel rail bolts than the stock size. I'd recommend substituting at least two of the M8x35mm fuel rail bolts for the M8x30mm intake runner ones. It worked fine for me.
These 35mm bolts are just barely too long (because of the tall head) to get into the passenger side front fuel rail hole and the driversside rear fuel rail hole without removing the runner tubes.
These 35mm bolts are just barely too long (because of the tall head) to get into the passenger side front fuel rail hole and the driversside rear fuel rail hole without removing the runner tubes.
#54
Drifting
Member Since: Apr 2004
Location: crystalriver Florida
Posts: 1,453
Likes: 0
Received 0 Likes
on
0 Posts
Re: F/S TPI/L98 stainless steel bolt set + special ball-end hex driver (CentralCoaster)
Hi, I got the bolts in yesterday, very cool....One question, I think I mentioned that I have the double sided bolt for my thermo unit. I got the 1 sided bolt, will this still be ok, just put the ground wire directly over the thermo and then slide bolt down through..the bolt should be the same thread size right? I don't have the car here with me at the moment to check?
#55
Team Owner
Thread Starter
Member Since: May 2002
Location: San Diego , CA Double Yellow DirtBags 1985..Z51..6-speed
Posts: 24,337
Likes: 0
Received 17 Likes
on
16 Posts
Re: F/S TPI/L98 stainless steel bolt set + special ball-end hex driver (chillcat)
chillcat, yeah, the stock bolt has the stud extending from it with the nut for the ground wire.
My vette has this too.. but I found that nut was a bitch to remove without the whole stud turning, and it was impossible to get a wrench on the bolt head below the groundwire... it was a pain in the butt all around....
Just throw that ground strap on there, and the washer, then the bolt, and you're good to go. :yesnod:
My vette has this too.. but I found that nut was a bitch to remove without the whole stud turning, and it was impossible to get a wrench on the bolt head below the groundwire... it was a pain in the butt all around....
Just throw that ground strap on there, and the washer, then the bolt, and you're good to go. :yesnod:
#56
Team Owner
Member Since: Sep 2003
Location: Freedom is never more than one generation away from extinction.
Posts: 20,161
Received 640 Likes
on
444 Posts
St. Jude '03-'04-'05-'06-'07-'08-'09-'10-'11-'12-'13-'14-'15-'16-'17-'18-‘19-'20-'21-'22-'23-'24
Re: F/S TPI/L98 stainless steel bolt set + special ball-end hex driver (CentralCoaster)
Package arrived today and looks great. Kevin did a nice job of organizing and packaging. Of particular note is the extra bag of spares that he so thoughtfully included. Now that's class!
:cheers: -JRC-
[Modified by JrRifleCoach, 10:52 PM 4/28/2004]
:cheers: -JRC-
[Modified by JrRifleCoach, 10:52 PM 4/28/2004]
#57
Team Owner
Thread Starter
Member Since: May 2002
Location: San Diego , CA Double Yellow DirtBags 1985..Z51..6-speed
Posts: 24,337
Likes: 0
Received 17 Likes
on
16 Posts
Re: F/S TPI/L98 stainless steel bolt set + special ball-end hex driver (CentralCoaster)
All sets have been shipped out. The last of you should receive them by next Thursday at the latest. I'll be doing another run of these with even more bolts when I get back in mid-May. Hell, I'll just IM all additional guys that expressed interest here. Stay tuned.
The bolt set works great. I got my fuel injectors back from Cruzin Performance, and slapped the entire sha-bang together in 45 minutes. I didn't use any washers, and it was a breeze with that allen driver. :yesnod:
The bolt set works great. I got my fuel injectors back from Cruzin Performance, and slapped the entire sha-bang together in 45 minutes. I didn't use any washers, and it was a breeze with that allen driver. :yesnod:
#58
Le Mans Master
Member Since: Jul 2002
Location: Alive and well in Burlington NC
Posts: 5,818
Likes: 0
Received 1 Like
on
1 Post
Re: F/S TPI/L98 stainless steel bolt set + special ball-end hex driver (CentralCoaster)
All I need to do is pick up a 4mm allen driver to do the valve covers and I'll be done. It kit looks great and it really is a time savings. One thing - if you have a long reach magnet in you tool box, go out and pick up a mechanic's long reach grabber (technical term :lol:) also.
Good job Kevin.
Good job Kevin.
#59
Team Owner
Thread Starter
Member Since: May 2002
Location: San Diego , CA Double Yellow DirtBags 1985..Z51..6-speed
Posts: 24,337
Likes: 0
Received 17 Likes
on
16 Posts
Re: F/S TPI/L98 stainless steel bolt set + special ball-end hex driver (Steel Blue 91)
All I need to do is pick up a 4mm allen driver to do the valve covers and I'll be done. It kit looks great and it really is a time savings. One thing - if you have a long reach magnet in you tool box, go out and pick up a mechanic's long reach grabber (technical term :lol:) also.
Good job Kevin.
Good job Kevin.
#60
Team Owner
Thread Starter
Member Since: May 2002
Location: San Diego , CA Double Yellow DirtBags 1985..Z51..6-speed
Posts: 24,337
Likes: 0
Received 17 Likes
on
16 Posts
Re: F/S TPI/L98 stainless steel bolt set + special ball-end hex driver (Steel Blue 91)
BTW.. I think the VC's use a 3/16" driver.. and the small distributor and TB plate screws use a 3mm driver. Damn metric and standard is all mixed up on this thing. Basically, everything that bolts into the block or heads is standard thread... everything else is metric. :yesnod: :smash: