flywheel question
Thread Starter
Burning Brakes
Joined: Feb 2004
Posts: 1,229
Likes: 0
From: Kansas City MO
flywheel question
My car had been making a screeching sound when i started it. I just found out that a tooth is missing from my flywheel. Is that going to be a problem? Other than the noise it makes right when I start it, there are not other noticible problems occuring. How much does it typically cost to get a flywheel replaced? I can't do the work myself.
Car info: 91 auto with 94k.
Car info: 91 auto with 94k.
Last edited by scofolo; Jul 20, 2005 at 04:45 PM.
Race Director
Joined: Dec 2002
Posts: 13,348
Likes: 233
From: SCMR Rat Pack'r Charter Member..Great Bend KS
Well, it's not going to get any better.....
It can damage the starter gear, that's about all.
You are probably looking at a minimum of $1000 for a new DM flywheel and the labor to install it.
Sorry I had to be the bearer of bad news.
Larry
code5coupe
It can damage the starter gear, that's about all.
You are probably looking at a minimum of $1000 for a new DM flywheel and the labor to install it.
Sorry I had to be the bearer of bad news.
Larry
code5coupe
Thread Starter
Burning Brakes
Joined: Feb 2004
Posts: 1,229
Likes: 0
From: Kansas City MO
Any idea how long a starter might last with a broken flywheel? I have a 1 year parts and labor warrenty on my new starter that I had installed last week. I guess I better keep that receipt in a safe place.
Team Owner
Joined: Jun 2005
Posts: 46,295
Likes: 2,596
From: Northern, VA
St. Jude Donor '15
"In honor of jpee"
Hmmm, rocco, is that $1k cost for the flywheel including the rest of the clutch assemby, bearings, facings, etc.? or is that just the flywheel + install? Thanks!
Race Director
Joined: Feb 2003
Posts: 11,672
Likes: 20
From: Lake Wylie SC
Wait a minute, didn't he say it was an auto? That said, he'll need a new flex plate. Still, mega bucks to remove the tranny to get at it. I can tell you how much it cost to remove and rebuild a Durango auto tranny, $2300. 
Race Director
Joined: Feb 2004
Posts: 12,518
Likes: 19
Figure $50 to buy a new flexplate. You can spend less. In my area $250 labor to r&i trans. Throw in 50 bucks to replace rear main seal on crankshaft amd front pump seal on trans. These are what I feel are average prices to do the job.
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
Top 10 Most Expensive Corvettes Ever Sold on Bring A Trailer
Brett Foote
10 Things Every Corvette Owner Needs (2026 Edition)
Michael S. Palmer
8 Most "Only Corvette Owners Understand" Quirks and Problems
Pouria Savadkouei
10 Reasons the C6 Z06 is Still A Performance Benchmark After 20 Years
Joe Kucinski
How Much Horsepower Every Corvette Engine "LOST" in 1972
Joe Kucinski
Top 10 DOs and DON'Ts for Protecting Your Convertible Top!
Michael S. Palmer
Top 10 Most Explosive Corvettes Ever Made: Power-to-Weight Ratio Ranked!
Joe Kucinski
150 hp to 1,250 hp: Every Corvette Generation Compared by the Specs That Matter
Joe Kucinski
8 Coolest Corvette Pace Cars (and Replicas) of All Time
Verdad Gallardo
Race Director
Joined: Feb 2004
Posts: 12,518
Likes: 19
Originally Posted by LT4CompYell
Man, those are some kind of reasonable rates in Nanticoke, Pete K.
Drifting
Joined: Jan 2005
Posts: 1,354
Likes: 325
From: San Antonio Tx
I drove with a missing flywheel tooth once years ago. If the motor happened to stop at just that spot the starter would just spin and not catch. I would have to turn the motor a little using the belt to get past that spot. And you know all about Murphy's law don't you?
