Jacking points on a C4.
Thread Starter
Race Director
Joined: Dec 2003
Posts: 14,132
Likes: 935
From: Fremont Ca
2022 C4 of the Year Finalist - Modified
Jacking points on a C4.
Somebody is always asking about where to raise a C4 with a floor jack.I was changing the oil and thought Id get a few pictures.I use the pinch weld in the frame,front and rear.The only problem with the rear is you need to watch for the E brake cables.I made these aluminum jack pads and then put some polyethylene plastic on that that.[IMG]
[/IMG][IMG]
[/IMG][IMG]
[/IMG]
[/IMG][IMG][/IMG][IMG][/IMG]
Drifting
Joined: Feb 2003
Posts: 1,614
Likes: 163
From: Davis CA
That's nice but it is overkill. After crawling under the car to place the floor jack in various locations, I finally just used the indicated places on the side. No problems. In fact, the front location can be used to lift both tires off the ground on that side. That makes switching wheels and tires easier.
Safety Car
Joined: Jan 2004
Posts: 3,759
Likes: 8
Does that lift the entire front end? And where are you putting the jack stands when you lift the front?
As I plan on pulling the knock sensor and oil cooler hoses on my 89 so I can do a coolant flush.
I didn't want to lift one side, then put a jack stand, then lift the other side, then put another jack stand.
I bought one of those low profile GM jacks with the light. I say it would be good to at least use a piece of wood inbetween the car and the jack pad? It so, how thick should it be and what type of wood?
As I plan on pulling the knock sensor and oil cooler hoses on my 89 so I can do a coolant flush.
I didn't want to lift one side, then put a jack stand, then lift the other side, then put another jack stand.
I bought one of those low profile GM jacks with the light. I say it would be good to at least use a piece of wood inbetween the car and the jack pad? It so, how thick should it be and what type of wood?
Thread Starter
Race Director
Joined: Dec 2003
Posts: 14,132
Likes: 935
From: Fremont Ca
2022 C4 of the Year Finalist - Modified
That's nice but it is overkill. After crawling under the car to place the floor jack in various locations, I finally just used the indicated places on the side. No problems. In fact, the front location can be used to lift both tires off the ground on that side. That makes switching wheels and tires easier.
I bought one of the G.M. floor jacks,total POS.
Safety Car
Joined: May 2007
Posts: 3,651
Likes: 10
From: Apple Valley MN
Does that lift the entire front end? And where are you putting the jack stands when you lift the front?
As I plan on pulling the knock sensor and oil cooler hoses on my 89 so I can do a coolant flush.
I didn't want to lift one side, then put a jack stand, then lift the other side, then put another jack stand.
I bought one of those low profile GM jacks with the light. I say it would be good to at least use a piece of wood inbetween the car and the jack pad? It so, how thick should it be and what type of wood?
As I plan on pulling the knock sensor and oil cooler hoses on my 89 so I can do a coolant flush.
I didn't want to lift one side, then put a jack stand, then lift the other side, then put another jack stand.
I bought one of those low profile GM jacks with the light. I say it would be good to at least use a piece of wood inbetween the car and the jack pad? It so, how thick should it be and what type of wood?
Safety Car
Joined: Jan 2004
Posts: 3,759
Likes: 8
Where do you put the jack stands at? And do you put anything on top of the jack puck and jack stands like a piece of wood? I'm assuming from the above post that is used to keep from causing marks into the car.
Safety Car
Joined: May 2007
Posts: 3,651
Likes: 10
From: Apple Valley MN
I put the jack stands on the pinch-welded section near the towing hooks. My floor jack has a rubber pad on it, but my stands don't. I would imagine it wouldn't be hard to glue some kind of thin rubber cushion to the stands. The only time I've used wood with a jack was when I jacked up the engine slightly to remove the balancer pulley - I used a 2x6 between the jack and the oil pan. Otherwise I don't think I'd recommend using something that isn't physically attached to the jack.
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
150 hp to 1,250 hp: Every Corvette Generation Compared by the Specs That Matter
Joe Kucinski
8 Coolest Corvette Pace Cars (and Replicas) of All Time
Verdad Gallardo
Top 10 Corvette Engines RANKED by Peak Torque (70+ Years of Muscle!)
Joe Kucinski
Corvette ZR1X Will Be Pacing the Indy 500, And Could Probably Race, Too!
Verdad Gallardo
Top 10 Corvettes Coming to Mecum Indy 2026!
Brett Foote
Top 10 C9 Corvette MUST-HAVES to Fix These C8 Generation Flaws!
Michael S. Palmer
10 Revolutionary 'Corvette Firsts' Most People Don't Know
Joe Kucinski
5 Reasons to Upgrade to an LS6-Powered Corvette; 5 Reasons to Stay LT2
Michael S. Palmer
2027 Corvette vs The World: Every C8 vs Its Closest Competitor
Joe Kucinski
Pro
Joined: Mar 2008
Posts: 579
Likes: 2
From: High Bridge New Jersey
Yup
That's nice but it is overkill. After crawling under the car to place the floor jack in various locations, I finally just used the indicated places on the side. No problems. In fact, the front location can be used to lift both tires off the ground on that side. That makes switching wheels and tires easier.
Thread Starter
Race Director
Joined: Dec 2003
Posts: 14,132
Likes: 935
From: Fremont Ca
2022 C4 of the Year Finalist - Modified
Most will see this as overkill but the way I see it,why leave a mark on something if it wasnt there before.This is how I work on my car,at least my ZR-1.When I place a jack stand under the car I do the same with some aluminum blocks.Ive seen pictures of that 89,very nice.
Thread Starter
Race Director
Joined: Dec 2003
Posts: 14,132
Likes: 935
From: Fremont Ca
2022 C4 of the Year Finalist - Modified
