Paging Red94Vette
Racer
Joined: Aug 2000
Posts: 491
Likes: 0
From: Houston, Texas
Re: Paging Red94Vette (Half Fast)
Well I need the engine torque/power curve and then the car data.
So either you have the R.W. dyno charts or I generate those using engine data with Desktop Dyno 2000.
Engine Data: Heads, Cam specs, Compression, CID, headers.
For the car data I need:
Race Weight
Tranny
Rear Gear
Rear Tires
Stall Converter/ or Launch RPM
Shift Points
That's about it. I'm in the middle of changing up the automatic part of my sim for the torque multiplication for the converter.
So either you have the R.W. dyno charts or I generate those using engine data with Desktop Dyno 2000.
Engine Data: Heads, Cam specs, Compression, CID, headers.
For the car data I need:
Race Weight
Tranny
Rear Gear
Rear Tires
Stall Converter/ or Launch RPM
Shift Points
That's about it. I'm in the middle of changing up the automatic part of my sim for the torque multiplication for the converter.
Thread Starter
Burning Brakes
Joined: Jun 2001
Posts: 838
Likes: 2
From: Out by the bridge again, TampaBay
Re: Paging Red94Vette (Red94Vette)
Well I need the engine torque/power curve and then the car data.
So either you have the R.W. dyno charts or I generate those using engine data with Desktop Dyno 2000.
http://temp.corvetteforum.net/c4/hal...//dscf0004.jpg
peak is: 361.8rwhp at 6200rpm, 324.2 rwtq@4750rpm
Engine Data: Heads, Cam specs, Compression, CID, headers.
Norris/CNC stage 3 heads 2.02/1.60, CC305 220/230 .544/.544, 10.8:1, 350CI, Hooker long tubes, no cats, Corsa
For the car data I need:
Race Weight 3500
Tranny 4L60E
Rear Gear 3.45
Rear Tires 285/35/17 RE730 or 315/35/17 Nitto DR
Stall Converter/ or Launch RPM Yank 3000
Shift Points 6200rpm
That's about it. I'm in the middle of changing up the automatic part of my sim for the torque multiplication for the converter.
[Modified by Half Fast, 11:40 PM 6/23/2002]
[Modified by Half Fast, 11:42 PM 6/23/2002]
So either you have the R.W. dyno charts or I generate those using engine data with Desktop Dyno 2000.
http://temp.corvetteforum.net/c4/hal...//dscf0004.jpg
peak is: 361.8rwhp at 6200rpm, 324.2 rwtq@4750rpm
Engine Data: Heads, Cam specs, Compression, CID, headers.
Norris/CNC stage 3 heads 2.02/1.60, CC305 220/230 .544/.544, 10.8:1, 350CI, Hooker long tubes, no cats, Corsa
For the car data I need:
Race Weight 3500
Tranny 4L60E
Rear Gear 3.45
Rear Tires 285/35/17 RE730 or 315/35/17 Nitto DR
Stall Converter/ or Launch RPM Yank 3000
Shift Points 6200rpm
That's about it. I'm in the middle of changing up the automatic part of my sim for the torque multiplication for the converter.
[Modified by Half Fast, 11:40 PM 6/23/2002]
[Modified by Half Fast, 11:42 PM 6/23/2002]
