The New King !
Thread Starter
Melting Slicks
Joined: Mar 2002
Posts: 3,426
Likes: 0
From: Toronto Ontario
The New King !
KING OF BLING 
I have been having trouble getting my car ready in time to hit the track this season, so I have put her into over drive this last week.
Big Stuff 3 - Check
Fuel System - Check
Turbo Kit - Check
Intercooler - Check
Forged 402 - Check !
BLING FACTOR - Check !!!
Believe it or not, I built this custom kit, had a friend help me drop in the motor. It was a busy week for my mechanic, so I did all this work my self. Needless to say my hands hurt like hell after 60 hours of slave labour. So I just have to measure up a belt due to the alternator relocation, and run some vacume line for the boost controller, wastegates, map sensor and catch can and I am finally ready for the DYNO !!
I know my Camera phone sucks, but which me luck getting her tuned next week boys !
I have been having trouble getting my car ready in time to hit the track this season, so I have put her into over drive this last week.
Big Stuff 3 - Check
Fuel System - Check
Turbo Kit - Check
Intercooler - Check
Forged 402 - Check !
BLING FACTOR - Check !!!
Believe it or not, I built this custom kit, had a friend help me drop in the motor. It was a busy week for my mechanic, so I did all this work my self. Needless to say my hands hurt like hell after 60 hours of slave labour. So I just have to measure up a belt due to the alternator relocation, and run some vacume line for the boost controller, wastegates, map sensor and catch can and I am finally ready for the DYNO !!
I know my Camera phone sucks, but which me luck getting her tuned next week boys !
Thread Starter
Melting Slicks
Joined: Mar 2002
Posts: 3,426
Likes: 0
From: Toronto Ontario
You had your chance way back when ... You will have to slit my throat and steal my car before I pull these headers off to copy for you.
Thread Starter
Melting Slicks
Joined: Mar 2002
Posts: 3,426
Likes: 0
From: Toronto Ontario
Custom Turbo Headers
Custom V-Band Collector (switch turbo size any time)
Custom V-Band Tial 44mm Wastegate Mounting
Custom V-Band 3" Downpipes (all the way back)
Custom V-Band GT35R's
Custom Intercooler
Custom Charge Pipes
Custom Fuel Rails
Custom Fuel Lines / Pumps
Custom Oil Cooler / Lines
Custom Water Pump Lines
Custom Coolant System
Custom Radiator
Custom Oil/Coolant Lines for the Turbo's
Custom Alternator & Bracket
Custom Power Steering Res / Lines
Custom Throttle Body
Big Stuff 3 ... etc etc.
Good luck getting started Uncle Roger ... Just stick with your maxed out direct port and be happy
Custom V-Band Collector (switch turbo size any time)
Custom V-Band Tial 44mm Wastegate Mounting
Custom V-Band 3" Downpipes (all the way back)
Custom V-Band GT35R's
Custom Intercooler
Custom Charge Pipes
Custom Fuel Rails
Custom Fuel Lines / Pumps
Custom Oil Cooler / Lines
Custom Water Pump Lines
Custom Coolant System
Custom Radiator
Custom Oil/Coolant Lines for the Turbo's
Custom Alternator & Bracket
Custom Power Steering Res / Lines
Custom Throttle Body
Big Stuff 3 ... etc etc.
Good luck getting started Uncle Roger ... Just stick with your maxed out direct port and be happy
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
Top 10 Most Expensive Corvettes Ever Sold on Bring A Trailer
Brett Foote
10 Things Every Corvette Owner Needs (2026 Edition)
Michael S. Palmer
8 Most "Only Corvette Owners Understand" Quirks and Problems
Pouria Savadkouei
10 Reasons the C6 Z06 is Still A Performance Benchmark After 20 Years
Joe Kucinski
How Much Horsepower Every Corvette Engine "LOST" in 1972
Joe Kucinski
Top 10 DOs and DON'Ts for Protecting Your Convertible Top!
Michael S. Palmer
Top 10 Most Explosive Corvettes Ever Made: Power-to-Weight Ratio Ranked!
Joe Kucinski
150 hp to 1,250 hp: Every Corvette Generation Compared by the Specs That Matter
Joe Kucinski
8 Coolest Corvette Pace Cars (and Replicas) of All Time
Verdad Gallardo
Thread Starter
Melting Slicks
Joined: Mar 2002
Posts: 3,426
Likes: 0
From: Toronto Ontario
6 Speed Upgrades ...
I managed to get DSS to make up some custom 300m Half Shafts & G-Force to make up a 300m Tranny main shaft for me. ECS made me a sick torque tube with u-joints rather than rubber pucks, and I have a McLeod Twin Disc Meba Clutch. I have the diff built up with DTE pinion support, 300m output shafts, and clutch pack/spring kit & brace. I figure the case will be the weakest link ... Pray for me
Here are some pictures :
300m vs Stock
I managed to get DSS to make up some custom 300m Half Shafts & G-Force to make up a 300m Tranny main shaft for me. ECS made me a sick torque tube with u-joints rather than rubber pucks, and I have a McLeod Twin Disc Meba Clutch. I have the diff built up with DTE pinion support, 300m output shafts, and clutch pack/spring kit & brace. I figure the case will be the weakest link ... Pray for me
Here are some pictures :
300m vs Stock
Last edited by LB; Nov 3, 2007 at 03:39 PM.
Melting Slicks
Joined: Feb 2006
Posts: 3,159
Likes: 247
From: LAS VEGAS NV
St. Jude Donor '08
Dang.. Nice setup!! .. looks strong. whats the ETA?
BTW: I am a little disturbed by you rabbit video on your profile .. you canadians have must go crazy in Jan/feb..with winter lol
BTW: I am a little disturbed by you rabbit video on your profile .. you canadians have must go crazy in Jan/feb..with winter lol
Last edited by vegasredz062; Nov 3, 2007 at 04:02 PM.
Thread Starter
Melting Slicks
Joined: Mar 2002
Posts: 3,426
Likes: 0
From: Toronto Ontario
Them wabbits be hunting YOU
