C5 Insulation "Mad-Mat" Kit... $185
#21
Former Vendor
Thread Starter
Member Since: Aug 2008
Location: Murfreesboro TN.
Posts: 2,168
Likes: 0
Received 0 Likes
on
0 Posts
C5 Pre-Cut Mad-Mat Full Insulation Kit
CLICK HERE TO ORDER!!!
$185 plus $20 shipping in the continental USA.
DOWNLOAD THE INSTRUCTIONS HERE!!!
The MadVette C5 Pre-cut Mad-Mat Insulation kit comes with everything you need to insulate and provide sound deadening in your Corvette, including Pre-cut pieces for your doors.
Other kits on the market provide a similar product, but do not provide pre-cut pieces for your doors, which allow road noise to be present in your front cabin. Our kit gives you everything you need to COMPLETELY insulate your C5 Corvette.
Our kit is a non-fiberglass, non-asphalt based product which weighs in at 3.5 lbs, for those who are weight conscious, it rejects 97% of the radiant heat, and has a manufacturer's rating of 19db of sound and road noise reduction!!! (please see the notes below on this... )
It is only 3/16" thick, so as not to interfere with proper mounting of your panels and seats, and all holes are pre-cut & all pieces are clearly labeled for your convenience.
It is our #1 goal to provide you ease of install, while making a HUGE improvement in your overall enjoyment of your Corvette!!!
Each kit is hand cut to our specifications, and guaranteed to make a dramatic difference in your C5!!!
Each kit comes with the following pieces:
It is only 3/16" thick, so as not to interfere with proper mounting of your panels and seats, and all holes are pre-cut & all pieces are clearly labeled for your convenience.
It is our #1 goal to provide you ease of install, while making a HUGE improvement in your overall enjoyment of your Corvette!!!
Each kit is hand cut to our specifications, and guaranteed to make a dramatic difference in your C5!!!
Each kit comes with the following pieces:
- Driver & Passenger front floorboard pieces, with holes cut for seat bolts and pedals.
- Driver & Passenger side tunnel pieces, cut around your e-brake.
- Full center console pieces, with holes for the center console bolts.
- Driver & Passenger side Door Panel pieces.
- Full Cargo area floor pieces.
- Full Side rear wheel well pieces.
- Full back wall and corner pieces.
- Full Center Well pre-cut pieces.
- Z06 % FRC come with roof pieces.
- Extra pieces for odds and ends coverage that you may need.
Say goodbye to over-heated center consoles, and noisy front cabins!! Our C5 kit is the perfect addition to your C5, and is recommended for every Corvette owner as the #1 modification for their Corvette!!!
Your Corvette will be cooler in the summer, alot less noisy, and you will regain use of your center console once again.
Alot of research and development has gone into this kit, and we are proud to say that our kit is made to our demanding specs, in house, and cut off of our own templates.
Some have emailed and asked, so here is a picture of the material, as well as some specs on the material itself:
It has 5 layers, and though it is rated at a 19db drop in noise, my customers have tested it in the Vettes at 8-11 db. reduction. Here are some manufacturer specs on it:
polyethylene backing
closed-cell Polyethylene foam
polyethylene backing
Aluminum Foil
Your Corvette will be cooler in the summer, alot less noisy, and you will regain use of your center console once again.
Alot of research and development has gone into this kit, and we are proud to say that our kit is made to our demanding specs, in house, and cut off of our own templates.
Some have emailed and asked, so here is a picture of the material, as well as some specs on the material itself:
It has 5 layers, and though it is rated at a 19db drop in noise, my customers have tested it in the Vettes at 8-11 db. reduction. Here are some manufacturer specs on it:
Characteristics | Value | Regulation
Cell Structure: Closed
Nominal Thickness: 5 mm (+ or - 0.5mm)
Steam Permeability: 0.033 gr/m2hkPa ASTM E-96
Noise Insulation: 19dBA IRAM 4063 at 50hz.
Flame Spread Index/Class: 25 or less/ "A" - Class 1 0 ASTM E-84
Smoke Index/Class: 450 or less/ "A" - Class 1 15 ASTM E-84
Cell Structure: Closed
Nominal Thickness: 5 mm (+ or - 0.5mm)
Steam Permeability: 0.033 gr/m2hkPa ASTM E-96
Noise Insulation: 19dBA IRAM 4063 at 50hz.
Flame Spread Index/Class: 25 or less/ "A" - Class 1 0 ASTM E-84
Smoke Index/Class: 450 or less/ "A" - Class 1 15 ASTM E-84
INSULATION LAYERS
Aluminum Foil polyethylene backing
closed-cell Polyethylene foam
polyethylene backing
Aluminum Foil
Pictures of the kit installed in a C5 vert are below.
Last edited by Madvette Motorsports; 09-30-2010 at 12:13 PM.
#23
Former Vendor
Thread Starter
Member Since: Aug 2008
Location: Murfreesboro TN.
Posts: 2,168
Likes: 0
Received 0 Likes
on
0 Posts
C5 Pre-Cut Mad-Mat Full Insulation Kit
CLICK HERE TO ORDER!!!
$185 plus $20 shipping in the continental USA.
DOWNLOAD THE INSTRUCTIONS HERE!!!
The MadVette C5 Pre-cut Mad-Mat Insulation kit comes with everything you need to insulate and provide sound deadening in your Corvette, including Pre-cut pieces for your doors.
Other kits on the market provide a similar product, but do not provide pre-cut pieces for your doors, which allow road noise to be present in your front cabin. Our kit gives you everything you need to COMPLETELY insulate your C5 Corvette.
Our kit is a non-fiberglass, non-asphalt based product which weighs in at 3.5 lbs, for those who are weight conscious, it rejects 97% of the radiant heat, and has a manufacturer's rating of 19db of sound and road noise reduction!!! (please see the notes below on this... )
It is only 3/16" thick, so as not to interfere with proper mounting of your panels and seats, and all holes are pre-cut & all pieces are clearly labeled for your convenience.
It is our #1 goal to provide you ease of install, while making a HUGE improvement in your overall enjoyment of your Corvette!!!
Each kit is hand cut to our specifications, and guaranteed to make a dramatic difference in your C5!!!
Each kit comes with the following pieces:
It is only 3/16" thick, so as not to interfere with proper mounting of your panels and seats, and all holes are pre-cut & all pieces are clearly labeled for your convenience.
It is our #1 goal to provide you ease of install, while making a HUGE improvement in your overall enjoyment of your Corvette!!!
Each kit is hand cut to our specifications, and guaranteed to make a dramatic difference in your C5!!!
Each kit comes with the following pieces:
- Driver & Passenger front floorboard pieces, with holes cut for seat bolts and pedals.
- Driver & Passenger side tunnel pieces, cut around your e-brake.
- Full center console pieces, with holes for the center console bolts.
- Driver & Passenger side Door Panel pieces.
- Full Cargo area floor pieces.
- Full Side rear wheel well pieces.
- Full back wall and corner pieces.
- Full Center Well pre-cut pieces.
- Z06 % FRC come with roof pieces.
- Extra pieces for odds and ends coverage that you may need.
Say goodbye to over-heated center consoles, and noisy front cabins!! Our C5 kit is the perfect addition to your C5, and is recommended for every Corvette owner as the #1 modification for their Corvette!!!
Your Corvette will be cooler in the summer, alot less noisy, and you will regain use of your center console once again.
Alot of research and development has gone into this kit, and we are proud to say that our kit is made to our demanding specs, in house, and cut off of our own templates.
Some have emailed and asked, so here is a picture of the material, as well as some specs on the material itself:
It has 5 layers, and though it is rated at a 19db drop in noise, my customers have tested it in the Vettes at 8-11 db. reduction. Here are some manufacturer specs on it:
polyethylene backing
closed-cell Polyethylene foam
polyethylene backing
Aluminum Foil
Your Corvette will be cooler in the summer, alot less noisy, and you will regain use of your center console once again.
Alot of research and development has gone into this kit, and we are proud to say that our kit is made to our demanding specs, in house, and cut off of our own templates.
Some have emailed and asked, so here is a picture of the material, as well as some specs on the material itself:
It has 5 layers, and though it is rated at a 19db drop in noise, my customers have tested it in the Vettes at 8-11 db. reduction. Here are some manufacturer specs on it:
Characteristics | Value | Regulation
Cell Structure: Closed
Nominal Thickness: 5 mm (+ or - 0.5mm)
Steam Permeability: 0.033 gr/m2hkPa ASTM E-96
Noise Insulation: 19dBA IRAM 4063 at 50hz.
Flame Spread Index/Class: 25 or less/ "A" - Class 1 0 ASTM E-84
Smoke Index/Class: 450 or less/ "A" - Class 1 15 ASTM E-84
Cell Structure: Closed
Nominal Thickness: 5 mm (+ or - 0.5mm)
Steam Permeability: 0.033 gr/m2hkPa ASTM E-96
Noise Insulation: 19dBA IRAM 4063 at 50hz.
Flame Spread Index/Class: 25 or less/ "A" - Class 1 0 ASTM E-84
Smoke Index/Class: 450 or less/ "A" - Class 1 15 ASTM E-84
INSULATION LAYERS
Aluminum Foil polyethylene backing
closed-cell Polyethylene foam
polyethylene backing
Aluminum Foil
Pictures of the kit installed in a C5 vert are below.
Last edited by Madvette Motorsports; 09-30-2010 at 12:14 PM.
#25
Former Vendor
Thread Starter
Member Since: Aug 2008
Location: Murfreesboro TN.
Posts: 2,168
Likes: 0
Received 0 Likes
on
0 Posts
C5 Pre-Cut Mad-Mat Full Insulation Kit
CLICK HERE TO ORDER!!!
$185 plus $20 shipping in the continental USA.
DOWNLOAD THE INSTRUCTIONS HERE!!!
The MadVette C5 Pre-cut Mad-Mat Insulation kit comes with everything you need to insulate and provide sound deadening in your Corvette, including Pre-cut pieces for your doors.
Other kits on the market provide a similar product, but do not provide pre-cut pieces for your doors, which allow road noise to be present in your front cabin. Our kit gives you everything you need to COMPLETELY insulate your C5 Corvette.
Our kit is a non-fiberglass, non-asphalt based product which weighs in at 3.5 lbs, for those who are weight conscious, it rejects 97% of the radiant heat, and has a manufacturer's rating of 19db of sound and road noise reduction!!! (please see the notes below on this... )
It is only 3/16" thick, so as not to interfere with proper mounting of your panels and seats, and all holes are pre-cut & all pieces are clearly labeled for your convenience.
It is our #1 goal to provide you ease of install, while making a HUGE improvement in your overall enjoyment of your Corvette!!!
Each kit is hand cut to our specifications, and guaranteed to make a dramatic difference in your C5!!!
Each kit comes with the following pieces:
It is only 3/16" thick, so as not to interfere with proper mounting of your panels and seats, and all holes are pre-cut & all pieces are clearly labeled for your convenience.
It is our #1 goal to provide you ease of install, while making a HUGE improvement in your overall enjoyment of your Corvette!!!
Each kit is hand cut to our specifications, and guaranteed to make a dramatic difference in your C5!!!
Each kit comes with the following pieces:
- Driver & Passenger front floorboard pieces, with holes cut for seat bolts and pedals.
- Driver & Passenger side tunnel pieces, cut around your e-brake.
- Full center console pieces, with holes for the center console bolts.
- Driver & Passenger side Door Panel pieces.
- Full Cargo area floor pieces.
- Full Side rear wheel well pieces.
- Full back wall and corner pieces.
- Full Center Well pre-cut pieces.
- Z06 % FRC come with roof pieces.
- Extra pieces for odds and ends coverage that you may need.
Say goodbye to over-heated center consoles, and noisy front cabins!! Our C5 kit is the perfect addition to your C5, and is recommended for every Corvette owner as the #1 modification for their Corvette!!!
Your Corvette will be cooler in the summer, alot less noisy, and you will regain use of your center console once again.
Alot of research and development has gone into this kit, and we are proud to say that our kit is made to our demanding specs, in house, and cut off of our own templates.
Some have emailed and asked, so here is a picture of the material, as well as some specs on the material itself:
It has 5 layers, and though it is rated at a 19db drop in noise, my customers have tested it in the Vettes at 8-11 db. reduction. Here are some manufacturer specs on it:
polyethylene backing
closed-cell Polyethylene foam
polyethylene backing
Aluminum Foil
Your Corvette will be cooler in the summer, alot less noisy, and you will regain use of your center console once again.
Alot of research and development has gone into this kit, and we are proud to say that our kit is made to our demanding specs, in house, and cut off of our own templates.
Some have emailed and asked, so here is a picture of the material, as well as some specs on the material itself:
It has 5 layers, and though it is rated at a 19db drop in noise, my customers have tested it in the Vettes at 8-11 db. reduction. Here are some manufacturer specs on it:
Characteristics | Value | Regulation
Cell Structure: Closed
Nominal Thickness: 5 mm (+ or - 0.5mm)
Steam Permeability: 0.033 gr/m2hkPa ASTM E-96
Noise Insulation: 19dBA IRAM 4063 at 50hz.
Flame Spread Index/Class: 25 or less/ "A" - Class 1 0 ASTM E-84
Smoke Index/Class: 450 or less/ "A" - Class 1 15 ASTM E-84
Cell Structure: Closed
Nominal Thickness: 5 mm (+ or - 0.5mm)
Steam Permeability: 0.033 gr/m2hkPa ASTM E-96
Noise Insulation: 19dBA IRAM 4063 at 50hz.
Flame Spread Index/Class: 25 or less/ "A" - Class 1 0 ASTM E-84
Smoke Index/Class: 450 or less/ "A" - Class 1 15 ASTM E-84
INSULATION LAYERS
Aluminum Foil polyethylene backing
closed-cell Polyethylene foam
polyethylene backing
Aluminum Foil
Pictures of the kit installed in a C5 vert are below.
Last edited by Madvette Motorsports; 09-30-2010 at 12:15 PM.
#26
your product vs Dynomat Extreme
I was going to install dynomat extreme in my c5 coupe can you tell me the difference betwwen your product and the dynomat product I like that your product is pre-cut I want to get rid of cabin noise. E-mail me at RMaxwell10@sbcglobal.net. Thanx Ray
#28
Former Vendor
Thread Starter
Member Since: Aug 2008
Location: Murfreesboro TN.
Posts: 2,168
Likes: 0
Received 0 Likes
on
0 Posts
C5 Pre-Cut Mad-Mat Full Insulation Kit
CLICK HERE TO ORDER!!!
$185 plus $20 shipping in the continental USA.
DOWNLOAD THE INSTRUCTIONS HERE!!!
The MadVette C5 Pre-cut Mad-Mat Insulation kit comes with everything you need to insulate and provide sound deadening in your Corvette, including Pre-cut pieces for your doors.
Other kits on the market provide a similar product, but do not provide pre-cut pieces for your doors, which allow road noise to be present in your front cabin. Our kit gives you everything you need to COMPLETELY insulate your C5 Corvette.
Our kit is a non-fiberglass, non-asphalt based product which weighs in at 3.5 lbs, for those who are weight conscious, it rejects 97% of the radiant heat, and has a manufacturer's rating of 19db of sound and road noise reduction!!! (please see the notes below on this... )
It is only 3/16" thick, so as not to interfere with proper mounting of your panels and seats, and all holes are pre-cut & all pieces are clearly labeled for your convenience.
It is our #1 goal to provide you ease of install, while making a HUGE improvement in your overall enjoyment of your Corvette!!!
Each kit is hand cut to our specifications, and guaranteed to make a dramatic difference in your C5!!!
Each kit comes with the following pieces:
It is only 3/16" thick, so as not to interfere with proper mounting of your panels and seats, and all holes are pre-cut & all pieces are clearly labeled for your convenience.
It is our #1 goal to provide you ease of install, while making a HUGE improvement in your overall enjoyment of your Corvette!!!
Each kit is hand cut to our specifications, and guaranteed to make a dramatic difference in your C5!!!
Each kit comes with the following pieces:
- Driver & Passenger front floorboard pieces, with holes cut for seat bolts and pedals.
- Driver & Passenger side tunnel pieces, cut around your e-brake.
- Full center console pieces, with holes for the center console bolts.
- Driver & Passenger side Door Panel pieces.
- Full Cargo area floor pieces.
- Full Side rear wheel well pieces.
- Full back wall and corner pieces.
- Full Center Well pre-cut pieces.
- Z06 % FRC come with roof pieces.
- Extra pieces for odds and ends coverage that you may need.
Say goodbye to over-heated center consoles, and noisy front cabins!! Our C5 kit is the perfect addition to your C5, and is recommended for every Corvette owner as the #1 modification for their Corvette!!!
Your Corvette will be cooler in the summer, alot less noisy, and you will regain use of your center console once again.
Alot of research and development has gone into this kit, and we are proud to say that our kit is made to our demanding specs, in house, and cut off of our own templates.
Some have emailed and asked, so here is a picture of the material, as well as some specs on the material itself:
It has 5 layers, and though it is rated at a 19db drop in noise, my customers have tested it in the Vettes at 8-11 db. reduction. Here are some manufacturer specs on it:
polyethylene backing
closed-cell Polyethylene foam
polyethylene backing
Aluminum Foil
Your Corvette will be cooler in the summer, alot less noisy, and you will regain use of your center console once again.
Alot of research and development has gone into this kit, and we are proud to say that our kit is made to our demanding specs, in house, and cut off of our own templates.
Some have emailed and asked, so here is a picture of the material, as well as some specs on the material itself:
It has 5 layers, and though it is rated at a 19db drop in noise, my customers have tested it in the Vettes at 8-11 db. reduction. Here are some manufacturer specs on it:
Characteristics | Value | Regulation
Cell Structure: Closed
Nominal Thickness: 5 mm (+ or - 0.5mm)
Steam Permeability: 0.033 gr/m2hkPa ASTM E-96
Noise Insulation: 19dBA IRAM 4063 at 50hz.
Flame Spread Index/Class: 25 or less/ "A" - Class 1 0 ASTM E-84
Smoke Index/Class: 450 or less/ "A" - Class 1 15 ASTM E-84
Cell Structure: Closed
Nominal Thickness: 5 mm (+ or - 0.5mm)
Steam Permeability: 0.033 gr/m2hkPa ASTM E-96
Noise Insulation: 19dBA IRAM 4063 at 50hz.
Flame Spread Index/Class: 25 or less/ "A" - Class 1 0 ASTM E-84
Smoke Index/Class: 450 or less/ "A" - Class 1 15 ASTM E-84
INSULATION LAYERS
Aluminum Foil polyethylene backing
closed-cell Polyethylene foam
polyethylene backing
Aluminum Foil
Pictures of the kit installed in a C5 vert are below.
#29
Former Vendor
Thread Starter
Member Since: Aug 2008
Location: Murfreesboro TN.
Posts: 2,168
Likes: 0
Received 0 Likes
on
0 Posts
I was going to install dynomat extreme in my c5 coupe can you tell me the difference betwwen your product and the dynomat product I like that your product is pre-cut I want to get rid of cabin noise. E-mail me at RMaxwell10@sbcglobal.net. Thanx Ray
Thanks!
Dave will email you later on today.....
Tim
#30
What kind of time do you estimate this to take? (Removal of interior, placement of mat, replacing interior)?
I've done this on restorations of old Datsuns, but never a "new" car.
I've done this on restorations of old Datsuns, but never a "new" car.
#32
Former Vendor
Thread Starter
Member Since: Aug 2008
Location: Murfreesboro TN.
Posts: 2,168
Likes: 0
Received 0 Likes
on
0 Posts
Tim
#34
Former Vendor
Thread Starter
Member Since: Aug 2008
Location: Murfreesboro TN.
Posts: 2,168
Likes: 0
Received 0 Likes
on
0 Posts
C5 Pre-Cut Mad-Mat Full Insulation Kit
CLICK HERE TO ORDER!!!
$185 plus $20 shipping in the continental USA.
DOWNLOAD THE INSTRUCTIONS HERE!!!
The MadVette C5 Pre-cut Mad-Mat Insulation kit comes with everything you need to insulate and provide sound deadening in your Corvette, including Pre-cut pieces for your doors.
Other kits on the market provide a similar product, but do not provide pre-cut pieces for your doors, which allow road noise to be present in your front cabin. Our kit gives you everything you need to COMPLETELY insulate your C5 Corvette.
Our kit is a non-fiberglass, non-asphalt based product which weighs in at 3.5 lbs, for those who are weight conscious, it rejects 97% of the radiant heat, and has a manufacturer's rating of 19db of sound and road noise reduction!!! (please see the notes below on this... )
It is only 3/16" thick, so as not to interfere with proper mounting of your panels and seats, and all holes are pre-cut & all pieces are clearly labeled for your convenience.
It is our #1 goal to provide you ease of install, while making a HUGE improvement in your overall enjoyment of your Corvette!!!
Each kit is hand cut to our specifications, and guaranteed to make a dramatic difference in your C5!!!
Each kit comes with the following pieces:
It is only 3/16" thick, so as not to interfere with proper mounting of your panels and seats, and all holes are pre-cut & all pieces are clearly labeled for your convenience.
It is our #1 goal to provide you ease of install, while making a HUGE improvement in your overall enjoyment of your Corvette!!!
Each kit is hand cut to our specifications, and guaranteed to make a dramatic difference in your C5!!!
Each kit comes with the following pieces:
- Driver & Passenger front floorboard pieces, with holes cut for seat bolts and pedals.
- Driver & Passenger side tunnel pieces, cut around your e-brake.
- Full center console pieces, with holes for the center console bolts.
- Driver & Passenger side Door Panel pieces.
- Full Cargo area floor pieces.
- Full Side rear wheel well pieces.
- Full back wall and corner pieces.
- Full Center Well pre-cut pieces.
- Z06 % FRC come with roof pieces.
- Extra pieces for odds and ends coverage that you may need.
Say goodbye to over-heated center consoles, and noisy front cabins!! Our C5 kit is the perfect addition to your C5, and is recommended for every Corvette owner as the #1 modification for their Corvette!!!
Your Corvette will be cooler in the summer, alot less noisy, and you will regain use of your center console once again.
Alot of research and development has gone into this kit, and we are proud to say that our kit is made to our demanding specs, in house, and cut off of our own templates.
Some have emailed and asked, so here is a picture of the material, as well as some specs on the material itself:
It has 5 layers, and though it is rated at a 19db drop in noise, my customers have tested it in the Vettes at 8-11 db. reduction. Here are some manufacturer specs on it:
polyethylene backing
closed-cell Polyethylene foam
polyethylene backing
Aluminum Foil
Your Corvette will be cooler in the summer, alot less noisy, and you will regain use of your center console once again.
Alot of research and development has gone into this kit, and we are proud to say that our kit is made to our demanding specs, in house, and cut off of our own templates.
Some have emailed and asked, so here is a picture of the material, as well as some specs on the material itself:
It has 5 layers, and though it is rated at a 19db drop in noise, my customers have tested it in the Vettes at 8-11 db. reduction. Here are some manufacturer specs on it:
Characteristics | Value | Regulation
Cell Structure: Closed
Nominal Thickness: 5 mm (+ or - 0.5mm)
Steam Permeability: 0.033 gr/m2hkPa ASTM E-96
Noise Insulation: 19dBA IRAM 4063 at 50hz.
Flame Spread Index/Class: 25 or less/ "A" - Class 1 0 ASTM E-84
Smoke Index/Class: 450 or less/ "A" - Class 1 15 ASTM E-84
Cell Structure: Closed
Nominal Thickness: 5 mm (+ or - 0.5mm)
Steam Permeability: 0.033 gr/m2hkPa ASTM E-96
Noise Insulation: 19dBA IRAM 4063 at 50hz.
Flame Spread Index/Class: 25 or less/ "A" - Class 1 0 ASTM E-84
Smoke Index/Class: 450 or less/ "A" - Class 1 15 ASTM E-84
INSULATION LAYERS
Aluminum Foil polyethylene backing
closed-cell Polyethylene foam
polyethylene backing
Aluminum Foil
Pictures of the kit installed in a C5 vert are below.
#35
Looks light as a feather or lighter. Great for anyone being careful with weight for weekend 1/4 mile runs, etc.. Fantastic to be light as a feather (execpt) for sound proofing.
Would be nice to also provide some instruction on adding some high mass (HEAVY) but not too much to the larger panels. NOT a criticism, just tell people to use a little heavy maybe Dynamat (Or generic for that) prior to the feathers and it would be hundreds of times better.
Looks like a good product to me, just attach a nice heavy mat prior.
Would be nice to also provide some instruction on adding some high mass (HEAVY) but not too much to the larger panels. NOT a criticism, just tell people to use a little heavy maybe Dynamat (Or generic for that) prior to the feathers and it would be hundreds of times better.
Looks like a good product to me, just attach a nice heavy mat prior.