Obx or bbk headers ???
Thread Starter
Intermediate
Joined: Sep 2009
Posts: 36
Likes: 0
From: MIAMI FLA.
Obx or bbk headers ???
GUYS
NEED SOME HELP AND ADVISE, IM THINKING OF PURCHASING HEADERS FOR MY 2001 COUPE. THE VEHICLE HAS COLD AIR INTAKE , Z06 TI-CAT BACK AND TUNE. MY QUESTION WHICH ONE OF THESE SHORTY HEADERS (DONT CARE FOR THE LONG TUBE GUYS, THATS NOT MY QUESTION PLEASE) ARE BEST FOR MY VETTE. WHICH ONE GOES ON EASIER AND REQUIRES LESS MODS IF ANY. DO I NEED TO GET BIGGER BOLTS, GASKETS ETC. OR DO THEY BOLT ON AND DRIVE ?
THANKS MANNY
NEED SOME HELP AND ADVISE, IM THINKING OF PURCHASING HEADERS FOR MY 2001 COUPE. THE VEHICLE HAS COLD AIR INTAKE , Z06 TI-CAT BACK AND TUNE. MY QUESTION WHICH ONE OF THESE SHORTY HEADERS (DONT CARE FOR THE LONG TUBE GUYS, THATS NOT MY QUESTION PLEASE) ARE BEST FOR MY VETTE. WHICH ONE GOES ON EASIER AND REQUIRES LESS MODS IF ANY. DO I NEED TO GET BIGGER BOLTS, GASKETS ETC. OR DO THEY BOLT ON AND DRIVE ?
THANKS MANNY
Le Mans Master
Joined: Aug 2005
Posts: 5,375
Likes: 328
From: CA.
St. Jude Donor '13-'14-'15
You should be able to use the same bolts---If the stock ones are not correct the manufacurer often includes a new set with the hdrs---
As far as the gaskets are concerned---I have found the stock GM 3-layer steel ones to be the best--Don't reuse the old ones as they are a one-time use item--They are a crush when tightening type gasket which makes an excellent seal---Either brand is fine---I think the BBK's are more expensive--probably a little better but most likely paying for the brand name--
As far as the gaskets are concerned---I have found the stock GM 3-layer steel ones to be the best--Don't reuse the old ones as they are a one-time use item--They are a crush when tightening type gasket which makes an excellent seal---Either brand is fine---I think the BBK's are more expensive--probably a little better but most likely paying for the brand name--
Team Owner
Joined: Dec 2008
Posts: 35,874
Likes: 1,600
From: Honolulu HI
Not sure where you live or if this even matters, but BBK's are 50 state smog legal. OBX's are cheaper because they didn't pay the premium to get a CARB EO#...and the fit and finish may not be as nice as BBK either. You may want to consider JBA shorties, as they are 50 state legal as well.
I would go with the BBK's or the JBA's, and order them ceramic coated from the manufacturer. I have B&B ceramic coated shorties and I'm very happy with them. You can find them for a real good deal if you shop around. Just my $0.02...
I would go with the BBK's or the JBA's, and order them ceramic coated from the manufacturer. I have B&B ceramic coated shorties and I'm very happy with them. You can find them for a real good deal if you shop around. Just my $0.02...
Team Owner
Joined: Dec 2008
Posts: 35,874
Likes: 1,600
From: Honolulu HI
Le Mans Master
Joined: Dec 2003
Posts: 5,047
Likes: 252
From: San Diego
Save your money on the shorty headers! Go with long tubes or nothing! A set of 01-04 Z06 exhaust manifolds are just as good as those brands you named. Save your money and buy a NOS kit, just my opinion though.
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
Top 10 Most Expensive Corvettes Ever Sold on Bring A Trailer
Brett Foote
10 Things Every Corvette Owner Needs (2026 Edition)
Michael S. Palmer
8 Most "Only Corvette Owners Understand" Quirks and Problems
Pouria Savadkouei
10 Reasons the C6 Z06 is Still A Performance Benchmark After 20 Years
Joe Kucinski
How Much Horsepower Every Corvette Engine "LOST" in 1972
Joe Kucinski
Top 10 DOs and DON'Ts for Protecting Your Convertible Top!
Michael S. Palmer
Top 10 Most Explosive Corvettes Ever Made: Power-to-Weight Ratio Ranked!
Joe Kucinski
150 hp to 1,250 hp: Every Corvette Generation Compared by the Specs That Matter
Joe Kucinski
