projector lights installation help
Thread Starter
Team Owner
Joined: Jul 2006
Posts: 22,808
Likes: 485
From: Douglas County WI
projector lights installation help
I began installing projector lights in my 02. Got to the part about hooking up wires. Totally baffled. Instructions aren't very helpful. Anyone out there done this recently that can give me an assist? PM for phone #. Thanks in advance
Thread Starter
Team Owner
Joined: Jul 2006
Posts: 22,808
Likes: 485
From: Douglas County WI
Got housings, ballasts, wiring, and all four bulbs from JW motorsports. I emailed him and am awaiting a response. In the meantime I am trying to figure what plugs into where. Instructions are very vague, at least to me. I seem to have more plugs than plugins or vice versa. Anyway, back out to the garage to carry on...
Last edited by glbeauchamp; Apr 23, 2018 at 04:38 PM.
Pro
Joined: May 2004
Posts: 746
Likes: 65
From: Phoenix, AZ
Unplug a factory light. Plug the factory light connector into a ballast input. Take the output of the ballast and plug it into the HID bulb. Do them one at a time and keep your wires neat, but make sure you leave enough wire for the lights to pop up. Secure the ballasts using two-sided tape or Velcro.
Did you get HID's for both the low and high beams? If so, you are going to want to wire your lights so that the low beams stay on when the high beams are activated, otherwise you will be blind when the low beams turn off while waiting for the high beams to warm up.
Unless you got high-end projectors, I'll bet you won't like them. I got eBay projectors and went back to the factory lenses. I love my HID lights, however. The high beams turn night into day after they warm up.
Did you get HID's for both the low and high beams? If so, you are going to want to wire your lights so that the low beams stay on when the high beams are activated, otherwise you will be blind when the low beams turn off while waiting for the high beams to warm up.
Unless you got high-end projectors, I'll bet you won't like them. I got eBay projectors and went back to the factory lenses. I love my HID lights, however. The high beams turn night into day after they warm up.
Last edited by TorqueWinsRaces; Apr 23, 2018 at 05:46 PM.
Thread Starter
Team Owner
Joined: Jul 2006
Posts: 22,808
Likes: 485
From: Douglas County WI
Unplug a factory light. Plug the factory light connector into a ballast input. Take the output of the ballast and plug it into the HID bulb. Do them one at a time and keep your wires neat, but make sure you leave enough wire for the lights to pop up. Secure the ballasts using two-sided tape or Velcro.
Did you get HID's for both the low and high beams? If so, you are going to want to wire your lights so that the low beams stay on when the high beams are activated, otherwise you will be blind when the low beams turn off while waiting for the high beams to warm up.
Unless you got high-end projectors, I'll bet you won't like them. I got eBay projectors and went back to the factory lenses. I love my HID lights, however. The high beams turn night into day after they warm up.
Did you get HID's for both the low and high beams? If so, you are going to want to wire your lights so that the low beams stay on when the high beams are activated, otherwise you will be blind when the low beams turn off while waiting for the high beams to warm up.
Unless you got high-end projectors, I'll bet you won't like them. I got eBay projectors and went back to the factory lenses. I love my HID lights, however. The high beams turn night into day after they warm up.
Le Mans Master
Joined: May 2006
Posts: 5,747
Likes: 224
From: Hillsboro Oregon
Thread Starter
Team Owner
Joined: Jul 2006
Posts: 22,808
Likes: 485
From: Douglas County WI
Those seem to be the housings I bought. I can't remember how to post pics but the ballasts (4) are black boxes 2 1/2 X 3" with 2 wires coming out the top, one a red wire with a two prong connector and a black wire that goes into a smaller black box that a black and a red wire come out of. They have single connectors that I think plug into the bulbs. The two prong connectors seem to plug into a double wire harness. There are four harnesses in two different lengths. Where they go is unknown to me. It almost seems like I don't have the correct main harnesses
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
Top 10 Most Expensive Corvettes Ever Sold on Bring A Trailer
Brett Foote
10 Things Every Corvette Owner Needs (2026 Edition)
Michael S. Palmer
8 Most "Only Corvette Owners Understand" Quirks and Problems
Pouria Savadkouei
10 Reasons the C6 Z06 is Still A Performance Benchmark After 20 Years
Joe Kucinski
How Much Horsepower Every Corvette Engine "LOST" in 1972
Joe Kucinski
Top 10 DOs and DON'Ts for Protecting Your Convertible Top!
Michael S. Palmer
Top 10 Most Explosive Corvettes Ever Made: Power-to-Weight Ratio Ranked!
Joe Kucinski
150 hp to 1,250 hp: Every Corvette Generation Compared by the Specs That Matter
Joe Kucinski
8 Coolest Corvette Pace Cars (and Replicas) of All Time
Verdad Gallardo
Le Mans Master
Joined: May 2006
Posts: 5,747
Likes: 224
From: Hillsboro Oregon
Melting Slicks
Joined: Jan 2009
Posts: 3,275
Likes: 739
From: Miami FL
It's not difficult 
Summary:
1. At your dialog box, click on the "Insert Image" icon. (it looks like a picture of a mountain).
(see first picture)
2. At the next page, click on the green bar that says "Browse your Device" and choose your photos. Click "Open" when you find them.
(see second picture)
3.Click "Insert" in the right upper corner to upload.
Picture No. 1:
Picture No. 2:
1. At your dialog box, click on the "Insert Image" icon. (it looks like a picture of a mountain).
(see first picture)
2. At the next page, click on the green bar that says "Browse your Device" and choose your photos. Click "Open" when you find them.
(see second picture)
3.Click "Insert" in the right upper corner to upload.
Picture No. 1:
Picture No. 2:
Last edited by GCG; Apr 24, 2018 at 09:44 AM.
Melting Slicks
Joined: Jan 2009
Posts: 3,275
Likes: 739
From: Miami FL
Last edited by GCG; Apr 24, 2018 at 09:45 AM.
Thread Starter
Team Owner
Joined: Jul 2006
Posts: 22,808
Likes: 485
From: Douglas County WI
As I am looking at the mess that will hopefully be headlights at some point, I am beginning to believe that two of the two wire harnesses are not the right ones. There are 4 total that I think plug into the ballasts. Two are 12" long with a 1/2" gap between prongs and work fine. The other two are 20" long with a 1/4" gap between prongs and don't seem to plug in anywhere. JWM has sent pictures that hopefully should help, so back into battle I go. I will check back here later.
Thread Starter
Team Owner
Joined: Jul 2006
Posts: 22,808
Likes: 485
From: Douglas County WI
JW Motorsports sent me a couple photos showing the hookups are supposed to go. With that and the assistance of a friend who knows more about this stuff than I do, we achieved success. All four lights work. Now to bolt everything back together. Thanks to all for your input.
By the way, while doing this project, I managed to break off one of the adjusting rods (just like I KNEW I would do). I suppose this means having to buy a whole new mounting frame?
By the way, while doing this project, I managed to break off one of the adjusting rods (just like I KNEW I would do). I suppose this means having to buy a whole new mounting frame?
Last edited by glbeauchamp; Apr 24, 2018 at 12:08 PM.
Melting Slicks
Joined: Jan 2009
Posts: 3,275
Likes: 739
From: Miami FL
